NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturers’ warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
25mm hole for passage sets.
Drill 2x 5mm holes through the door where through-bolt fixing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt fixing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from floor)
4444
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3333
3
1111
1
2222
2
P R E P AR E J AMB & INS TALL S TR IK E
INS TALL LATC H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate fits flush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5555
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill 2x 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and install strike.
(Privacy Set illustrated)
(Universal Strike illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt fixing. Cut bolts to appropriate length,
flush against the rose.
Fit self-tapping wood screws to each rose as necessary.
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturers’ warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
25mm hole for passage sets.
Drill 2x 5mm holes through the door where through-bolt fixing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt fixing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from floor)
4444
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3333
3
1111
1
2222
2
P R E P AR E J AMB & INS TALL S TR IK E
INS TALL LATC H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate fits flush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5555
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill 2x 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and install strike.
(Privacy Set illustrated)
(Universal Strike illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt fixing. Cut bolts to appropriate length,
flush against the rose.
Fit self-tapping wood screws to each rose as necessary.
1
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturers’ warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
25mm hole for passage sets.
Drill 2x 5mm holes through the door where through-bolt fixing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt fixing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from floor)
4444
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3333
3
1111
1
2222
2
P R E P AR E J AMB & INS TALL S TR IK E
INS TALL LATC H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate fits flush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5555
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill 2x 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and install strike.
(Privacy Set illustrated)
(Universal Strike illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt fixing. Cut bolts to appropriate length,
flush against the rose.
Fit self-tapping wood screws to each rose as necessary.
WARNING:
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturing warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
20mm hole for passage sets.
Drill (2) 5mm holes through the door where through-bolt fixing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt fixing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from floor)
4444
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3333
3
1111
1
2222
2
P R E P AR E J AMB & INS TALL S TR IK E
INS TALL LATC H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate fits flush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5555
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill (2) 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and
install strike.
(Privacy Set Illustrated)
(Universal Strike Illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt fixing. Cut bolts to appropriate length,
flush against the rose.
Fit self-tapping wood screws to each rose as necessary.
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturers’ warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
25mm hole for passage sets.
Drill 2x 5mm holes through the door where through-bolt fixing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt fixing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from floor)
4444
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3333
3
1111
1
2222
2
P R E P AR E J AMB & INS TALL S TR IK E
INS TALL LATC H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate fits flush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5555
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill 2x 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and install strike.
(Privacy Set illustrated)
(Universal Strike illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt fixing. Cut bolts to appropriate length,
flush against the rose.
Fit self-tapping wood screws to each rose as necessary.
NOTE:
All applications involving door closers require 2x through-fixing screws
and 2x self-tapping wood screws to be fitted to each rose.
Failure to do so may void manufacturers’ warranty.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Accurate door preparation is essential for the functioning of this lock.
Please follow the enclosed template and instructions carefully.
Through-bolt fixing is recommended.
Drill a 35mm hole through the door for privacy sets and a
C
25mm hole for passage sets.
Drill 2x 5mm holes through the door where through-bolt fixing
is required.
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.
Mark holes for through-bolt fixing where required.
A
B
C
Fold template at correct height
(suggested height for centreline is 970mm from floor)
4444
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3333
3
1111
1
2222
2
P R E P AR E J AMB & INS TALL S TR IK E
INS TALL LATC H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Chisel out wood until facepate fits flush with door edge.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5555
5
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill 2x 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and install strike.
(Privacy Set illustrated)
(Universal Strike illustrated)
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt fixing. Cut bolts to appropriate length,
flush against the rose.
Fit self-tapping wood screws to each rose as necessary.
A. 7000/9000 privacy sets have a plastic stop inserted on
each side to prevent the handle rotating upwards. This is only
required for models with square handles (to avoid privacy pin
breakage).
A.
Door Preparation
Drill Holes
Install Latch
Prepare Jamb and Install Strike
Remove Rose Caps
Install Furniture
Insert spindles into furniture, as illustrated.
Attach furniture to door by through-bolt fixing. Cut bolts to
appropriate flush against the rose. Fit self-tapping wood screws to each
rose as necessary.
A
B
6
5
4
3
2
7000/9000 and Medio Series
Installation Instructions
6000/8000 Series
Installation Instructions
