background image

75.5306.02 ALLEGION TIME-DELAY MODULE 8310-845 20180702 

 

Page 1 of 4

8310-845 TIME-DELAY MODULE

PRECAUTIONS

75.5306.02 ALLEGION TIME-DELAY MODULE 8310-845 20180702 

 

Page 1 of 4

Delay-on-make / Delay-on-break time relay

ENGLISH

DESCRIPTION

TECHNICAL SPECIFICATIONS

Power supply:

15 – 24 VAC/VDC -5 – 10%

Operating frequency:

4 MHz (microprocessor)

Power consumption:

10 mA at rest; 50 mA max.

Output:

2 SPST relays

Max. voltage (relay contact):

30 VDC / 120 VAC

Max. current (relay contacts):

1.0A DC / 0.5A AC

Specifications are subject to change without 

prior notice.

All values measured in specific conditions.

 

‰

Shut off all power going to header before attempting any wiring procedures.

 

‰

Maintain a clean and safe environment when working in public areas.

 

‰

Constantly be aware of pedestrian traffic around the door area. 

 

‰

Always stop pedestrian traffic through the doorway when performing tests that may result in 
unexpected reactions by the door.

 

‰

ESD (electrostatic discharge)

:  Circuit boards are vulnerable to damage by electrostatic discharge. 

Before handling any board, ensure you dissipate your body’s ESD charge.

 

‰

Always check placement of all wiring before powering up to ensure that moving door parts will not 
catch any wires and cause damage to equipment.

 

‰

Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of 
installation.

 

‰

DO NOT attempt any internal repair of the components. Unauthorized disassembly or repair:

1.  May jeopardize personal safety and may expose one to the risk of electrical shock.
2.  May adversely affect the safe and reliable performance of the product resulting in a voided 

warranty.

Содержание LCN 8310-845

Страница 1: ... working in public areas Constantly be aware of pedestrian traffic around the door area Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door ESD electrostatic discharge Circuit boards are vulnerable to damage by electrostatic discharge Before handling any board ensure you dissipate your body s ESD charge Always check placement...

Страница 2: ...OM contact RELAY 1 N O contact RELAY 1 N C contact BLACK RED GRAY GRAY ORANGE PURPLE BROWN GREEN BLUE YELLOW JP1 1 4 JP2 JP 1 JP 2 1 4 TIME DELAY NO COM Push Plate Motion Sensor etc DRY INPUT 24 VAC Can either be a wet or dry output depending on position of jumpers R E L A Y 1 R E L A Y 2 GRAY GRAY GREEN YELLOW BLUE NC COM NO PURPLE NC RED COM BLACK NO ORANGE BROWN NOTE Unused wires must be inslul...

Страница 3: ... LED indicates RELAY 2 is active and sending signal to door control to hold door open DELAY OPTION Time delay between Relay 1 being activated and Relay 2 being activated OFF ON 7 6 5 4 3 2 1 green LED safety beams red LED lock out time 8 RED LED RELAY 1 active GREEN LED RELAY 2 active JP1 JP2 1 4 BLUE GREEN YELLOW GRAY ORANGE GRAY BROWN RED BLACK PURPLE DRY OUTPUT ON RELAY 1 BLUE GREEN YELLOW GRAY...

Страница 4: ...the door gate manufacturer recommendations and or per AAADM ANSI DASMA guidelines where applicable for best industry practices Safety inspections must be performed during each service call examples of these safety inspections can be found on an AAADM safety information label e g ANSI DASMA 102 ANSI DASMA 107 Verify that all appropriate industry signage and warning labels are in place INSTALLATION ...

Отзывы: