manualshive.com logo in svg

Alienware m17 P37E, Руководство по обслуживанию

Поделиться
Скачать
Alienware m17 P37E Скачать руководство пользователя страница 51

Replacing the heat sink

WARNING: Before working inside your computer, read the safety information that shipped with your computer and 

follow the steps in 

Before working inside your computer

. After working inside your computer, follow the instructions 

in 

After working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at 

www.dell.com/regulatory_compliance

.

CAUTION: Incorrect alignment of the heat sink can damage the system board and processor.

NOTE: If either the system board or the heat sink is replaced, use the thermal pad/paste provided in the kit to 

ensure that thermal conductivity is achieved.

Procedure 

1 

Replace the 

fans

.

2  Place the heat-sink assembly on the system board and align the screw holes on the heat-sink assembly with the screw holes 

on the system board.

3  Tighten the captive screws in the sequential order (1>2>3>4>5>6>7) to secure the heat-sink assembly to the system 

board.

4  Replace the four screws (M2x3) that secure the heat-sink assembly to the system board.
5  Connect the left fan cable to the system board.
6  Connect the right fan cable to the system board.

51

Содержание m17 P37E
















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды