1
www.observint.com
ALI-TS7012V_CQ
170224
—
RS-485 address: 0
—
Baud Rate: 2400
—
RS-485 termination resistor: Off
Using the tables below, set the switches in accordance with the following:
•
The address of each device (camera) on the RS-485 network must be different.
•
The baud rate must be the same for each device on the RS-485 network.
•
The DIP switches 1 - 9, used for setting the address, baud rate, and protocol of the RS-485 network,
function logically in this way: ON=1 and OFF=0.
•
The camera is self-adaptive to the Pelco-P, Pelco-D and Private-Code protocols. You don’t have to set
the DIP switches for these RS-485 control protocol.
•
DIP switch 10 provides RS-485 end-of-line termination and cannot be set using the DVR interface. If
used, it must be set by opening the camera enclosure and manually setting the switch to ON.
To set the DIP switches manually, do the following:
1.
Remove the lower dome cover from the camera by extracting the three screws.
Dome screws (3)
Dome
Remove lower dome
2.
Locate the DIP switches inside the housing.
DIP switches
a.
For DIP switches 1 .. 10 (SW1 .. SW10), use SW1 .. SW5 to set the RS-485 network address
according to the table below.
Camera address
SW 1
SW 2
SW 3
SW 4
SW 5
0
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
:
:
:
:
:
:
28
OFF
OFF
ON
ON
ON
29
ON
OFF
ON
ON
ON
30
OFF
ON
ON
ON
ON
31
ON
ON
ON
ON
ON
ALI-TS7012V 2.0MP 23x Zoom
HD-TVI Outdoor PTZ Camera
Quick Installation Guid
e
The ALIBI™ ALI-TS7012V HD-TVI outdoor PTZ camera enables you to pan, tilt and zoom in on suspicious
activity and capture high definition video of wide areas such as parking lots, shopping malls and sports
facilities. The camera features:
•
2.0 MP CMOS image sensor
•
On-screen displays (OSD) for configuration and programming
•
1080p HD-TVI and CVBS video output
•
23X optical zoom, 16X digital zoom
•
Privacy Masking, 3D DNR, D WDR, EIS, true Day&Night
•
3D intelligent positioning
•
24 Vac power supply included
•
Seven mounting bracket options (see
Specifications
section)
For more information about this camera, including use of the On-screen displays (OSD), lightening
protection, RS-485 bus design and general warnings and cautions, refer to the
ALI-TS7012V 2.0MP
HD-TVI 23x Zoom Outdoor PTZ Camera User Manual
available from your vendor.
What’s in the box
This product includes:
•
24 Vac power supply
•
Security wrench
•
Gloves
What you need
•
Tools and additional fasteners (may be required) for mounting the camera and mounting bracket
•
Video and power extension cable
•
HD-TVI or CVBS video setup monitor (optional)
•
HD-TVI compatible (Alibi) security video recorder
Before you start, check the package contents and make sure that the device in the package is in good
condition and all the assembly parts are included.
Step 1. Set the DIP switches
DIP switches, located in the housing are used to setup the RS-485 network address (switches 1 - 5), baud
rate (switches 6 - 7), protocol (switches 8 - 9) and TVI mode (switch 10). These switches can also be setup
manually or through the DVR PTZ interface. Two additional switches are provided for RS-485 network
termination. The default DIP switch settings configure the camera for:
