1
www.observint.com
ALI-TP1002LS_CQ
191120
Switch
button
Cap for switch
cable
12 Vdc power in
Video BNC
connector
Alarm out screw-
down terminals
Camera drop cable connectors
What’s in the box
Box contains:
•
Installation Guide
•
Drill template
•
Mounting screws and wall inserts
What you need
To install the camera, you will need:
•
12 Vdc power source. See
Specifications
for requirements.
•
Tools and additional fasteners (may be required) for mounting the camera
•
Video, power and ground (if needed) extension cables
Installation
Before installation:
•
Make sure that the device is in good condition and all the assembly parts are included.
•
Check the specification of the products for the installation environment.
•
Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the
camera.
•
To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the
Specifications
section.
During installation:
•
Camera Lens
: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning
section.
•
Power supply
:
Camera drop cable
: The camera drop cable includes two connectors:
—
Video BNC connector
: For transmission of the video signal across a coax (75 Ω) extension
cable to a compatible recorder.
—
Power connector:
The camera can be powered by 12 Vdc. When applying 12 Vdc power,
observe the power polarity shown on the connector. See the picture to the left for the connector
polarity configuration.
Step 1. Route interface cables to the camera
Video and power interface cables connect directly to the camera drop cable (see photo above).
NOTE
When selecting a mounting location for the camera
• Make sure that there are no reflective surfaces near to the camera lens. White light from the camera
may bounce back onto the lens causing reflections.
• Determine how wiring is routed into the camera. The cable can be routed through an access hole in the
mounting plate, or through the cable in the mounting base.
The camera includes connectors for the following:
•
Video coax
(required): The video drop cable can connect to a video coax extension cable from a
Video Recorder or compatible monitor.
•
12 Vdc power input
(optional if PoE powered, required if not): Refer to the Specifications section
of this document for voltage and current requirements. ALWAYS COMPLY WITH THE POLARITY
SHOWN IN THIS GUIDE.
•
Alarm output
for connection to a reporting device.
1.
Route a video coax extension cable from a compatible video recorder (DVR) to where the camera
will be installed.
2.
Route 12 Vdc power extension cables from an adequate power source to the location where the
camera will be installed.
ALI-TP1002LS 2 MP
4-in-1
Turret
Camera with Strobe and Siren
Quick Installation Guide
The ALIBI ALI-TP1002LS indoor / outdoor turret camera includes a 4 -in-1 switchable video output (TVI/
AHD/CVI/CVBS) with a 2 MP sensor and Starlight technology for color vision at night. This camera features:
•
2 Megapixel (1920
1080 pixels) wyth CMOS sensor
•
Switchable video output for TVI, AHD, CVI, or CVBS (4 in 1)
•
24 hour color image
•
Starlight 2.0 chipset
•
3.6 mm fixed lens offers horizontal FOV of 83.6°
•
True WDR up to 130 dB
•
PIR Detection, Strobe light alarm, alarm out / audible siren alarm
•
IP67 weather-rated with -40°F – 140°F operating temperatures
•
OSD menu (up-the-coax OSD control)
•
Compatible with ALI-AB1 Wall mount adapter, ALI-AA1 pole mount adapter, ALI-AA2 outdoor
corner mount adapter, ALI-AB1 short wall mount bracket with J-box, ALI-AB2 long wall mount
bracket with J-box, ALI-AF1 flange plate, and ALI-AJ1 round junction box.
Camera
body
Enclosure
Orientation
mark “
UP
”
Mounting
base
Lens
White light LED
ALI-TP1002LS camera
Drop
cable
Mounting
screw
holes (3)
Mounting
base
Camera
body
Mounting base - mounting surface
