1
THE TASK PURPOSE OF THIS MANUAL
The purpose of the instructions is to enable the user to take all the necessary measures in order to ensure safe and proper
use of the stove.
UPDATING THE INSTRUCTIONS
This manual reflects a work of art at the moment when the stove was placed on the market. Therefore, Alfa Plam does not
take into account the stoves that are already on the market with the appropriate technical documentation and considers them
as defective or inadequate after any kind of modification, adaptation or application of new technologies to newly produced
machines.
The contents of this manual should be carefully read and studied. It is necessary to strictly follow all the instructions given
in this manual. All information contained in this manual is necessary for proper connection, use, and maintenance of your
stove.
Therefore, this manual has to be carefully stored for the necessary instructions in the event of any problems or concerns.
If the stove is given or sold to another person, the new owner must also be given this instructions manual.
If you have lost your manual, the manufacturer can provide you with a new one.
RESPONSIBILITIES OF THE MANUFACTURER
In issuing these instructions, Alfa Plam accepts no civil or legal liability, direct or indirect, due to:
- Accidents caused by not respecting the standards and specifications given in this manual,
- Accidents caused by improper handling or use of the stove by the user,
- Accidents resulting from modifications and repairs, which were not approved by Alfa Plam,
- Poor maintenance,
- Unforeseen events,
- Accidents resulting from the use of spare parts that were not original or not intended for these models of stoves.
Responsibility for connecting is fully assumed by the installer - contractor.
GENERAL CHARACTERISTICS OF USERS
The user of the appliance must have the following basic characteristics:
- be an adult and responsible person,
- have a specific technical knowledge that is needed for routine maintenance of electrical and mechanical components of
the stove.
CHILNDREN ARE NOT ALLOWED NEAR THE STOVE OR TO PLAY WITH IT WHILE IT IS ON.
TRANSPORTING AND USING THE STOVE - HANDLING
When using the stove, it is necessary to be careful and not allow the stove to tilt forward. This is because the brunt of the
stove is forward.
During transportation of the stove, which has to be completely safe, make sure that the forklift has the load that is greater
than the weight of the stove that it is supposed to lift. Avoid twitching and jerking movements.
ALL PACKAGING SHOULD BE REMOVED SO THAT IT IS OUT OF REACH OF CHILDREN, BECAUSE THE MATERIALS THAT
ARE INSIDE CAN LEAD TO CHILDREN SUFFOCATING. THESE INCLUDE PLASTIC BAGS, FILM, POLYSTYRENE, ETC.
RESPONSIBILITIES OF THE INSTALLER
Installer's responsibility is to do all the tests of the flue pipeline, air supply, and all the things that are necessary for
connecting (installing) your stove.
Installer's responsibility is to adjust the stove to local regulations which apply where the stove is connected (installed).
The use of the stove must be in accordance with the instructions for use and maintenance, as well as with all the security
standards that are given by the local regulations that apply where the stove is connected (installed).
The installer has to check:
- the type of stove to be connected,
- whether the room corresponds to the stove where the stove will be installed, which is expressed as the minimum size
required for installation, set forth by the manufacturer of the stove,
- heat generator
- manufacturer's instructions regarding the requirements of smoke removal systems (ducts and pipes for
smoke exhaust),
- inner cross section of the chimney, the material out of which the chimney is made, uniform cross section,
- that there are no disturbances and obstacles in the chimney,
- height and vertical extension of the chimney,
- altitude at the place of connecting the stove,
- the existence and suitability of the protective cover for the chimney that is resistant to the wind,
- the possibility of securing the external air supply and the size of the necessary openings,
- simultaneous use of stove that needs to be connected with other equipment that already exists at that
place.
If the results of all checks are positive, then we can proceed with connecting the stove. Make sure you follow the
instructions of the manufacturer of the stove, as well as the standards for fire protection and the safety standards provided.
When you are finished connecting, the stove has to be turned on in trial mode for at least 30 minutes to test if the stove is
working properly.
When the installation and important details are completed, the installer must provide the client the following:
