manualshive.com logo in svg

Alfa Laval M line TS6, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval M line TS6 Скачать руководство пользователя страница 43

6.7.1 Clip-on / ClipGrip

1

Open the heat exchanger, refer to 

Opening

on page 34.

 NOTE

Before opening the heat exchanger,
check the warranty conditions. If in any
doubt, contact the Alfa Laval sales
representative. Refer to 

Warranty

conditions

 on page 7.

2

Remove the old gasket with the plate still
hanging in the frame.

3

Make sure that all sealing surfaces are dry,
clean and free of foreign matter such as fat,
grease or similar.

4

Check the gasket and remove rubber residual
before attaching it.

 NOTE

Especially the end plate gasket!

5

Attach the gasket to the plate. Slip the gasket
tabs under the edge of the plate.

 NOTE

Make sure the two gasket prongs are in
the correct position.

Clip-on

ClipGrip

6

Repeat the procedure until all plates that are
needed to be regasketed are done. Close the
heat exchanger according to 

Closing

 on page

39.

200000423-1-EN-GB

43

Maintenance 6

EN

Содержание M line TS6















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды