manualshive.com logo in svg

Alfa Laval M line TS6, Инструкция по эксплуатации

Поделиться
Скачать
Alfa Laval M line TS6 Скачать руководство пользователя страница 11

3 Description

3.1 Components

1

2

6

4

7

5

3

8

Main components

1. Frame plate

Fixed plate with a various number of portholes for the connection of the
piping system. The carrying and guiding bar are attached to the frame
plate.

2. Carrying bar

Carries the plate pack and the pressure plate.

3. Plate pack

Heat is transferred from one media to the other through the plates. The
plate pack consists of channel plates, end plates, gaskets and in some
cases transition plates. The measurement of the plate pack is the

 A

dimension, i.e the measurement between frame plate and pressure plate.
Refer to the PHE drawing.

4. Pressure plate

Moveable plate that can contain a various number of portholes for the
connection of the piping system.

5. Guiding bar

Keeps the channel plates, connection plates and the pressure plate
aligned at their lower end.

6. Support column

Supports carrying and guiding bars.

7. Tightening bolts

Compress the plate pack between the frame plate and the pressure plate.
Remaining bolts are used as locking bolts.

8. Sanitary connections

Pipes with sanitary fittings or flanges allow the media to enter into or exit
from the heat exchanger.

200000423-1-EN-GB

11

EN

Содержание M line TS6















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды