ALE TC Series Скачать руководство пользователя страница 2

Страница: 2 / 18

Design • Print • Trace

07/07/2011

Disclaimer

This manual contains instructions for operating the

ALE

TC18, TC54 and

TC72 print-heads. Read it carefully before performing any manipulation.

All service operations should be undertaken by qualified personnel only.

Contact-us if you need training for our equipment.

All information written in this Operator Manual was correct at the time

indicated in the version table below. However, the continual enhancement of
our products may result in some differences existing between the
information contained in this document and your equipment.

ALE

whole or part without permission is expressly prohibited.

RiX® and TraceX® are registered trademarks of

ALE

sarl.

All trademarks in this document belong to their respective owners.

Version history:

Date:

Revision:

Modifications:

Author:

22/03/10

First version

11/08/10

+TC54

AF/GP

30/08/10

#2.1

Small corrections

06/09/10

#2.2

+"Bottle replacement" section

07/07/2011

+TC18

TC Series Operator Manual

Содержание TC Series



















Результаты поиска

Содержание TC Series

Отзывы:

ALE TC Series, Руководство оператора, Страница: 2 / 18

Результаты поиска

Содержание TC Series

Отзывы: