Alcatel OmniSwitch 6800 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 86

background image

New Hardware Supported

OmniSwitch 6800/6850/9000—Release 6.1.3.R01

page 7

New Power over Ethernet Components/Enhancements

OmniSwitch 9000 OS-IP-SHELF PoE Power Shelf

The OS-IP-SHELF unit is the peripheral power shelf for the chassis that provides the electrical current
used for PoE ports. Up to four 600W OS-IP-SHELF specific power supply modules are available. These
are load sharing modules that can provide up to a maximum of 2400W PoE power source.

OmniSwitch 9600 Support for

PS-510W AC/PS-360W AC

The 510W and 360W power supplies can be used as an alternate power source for PoE on the OmniSwitch
9600. A single 510W power supply allocates 380W for the PoE functionality; Similarly, a single 360W
power supply allocates 230W for the PoE functionality. Only one power supply module can be installed
per switch, not both. These power modules support load sharing across all the POE NIs in the OmniSwitch
9600 chassis.

Note that the 510W/360W power supplies are only supported on the OmniSwitch 9600 and not on the
OmniSwitch 9700 or OmniSwitch 9800.

New Ethernet Transceivers (SFPs)

The following Gigabit Ethernet, dual-speed Ethernet, and 100FX Ethernet transceivers are available in this
release:

Gigabit Ethernet Transceiver (SFP MSA)

SFP-GIG-T

- 1000Base-T Gigabit Ethernet Transceiver (SFP MSA) - Supports category 5, 5E, and 6

copper cabling up to 100m. SFP only works in 1000 Mbit/s speed and full-duplex mode.

Dual Speed Ethernet Transceivers

SFP-DUAL-MM

- Dual Speed 100Base-FX or 1000Base-X Ethernet optical transceiver (SFP MSA).

Supports multimode fiber over 1310nm wavelength (nominal) with an LC connector. Typical reach of
550m at Gigabit speed and 2km at 100Mbit speed.

Note:

•

at 100Mbit speed, this SFP can interoperate with SFP-100-LC-MM or similar transceiver on the other
end.

•

at Gigabit speed, this SFP cannot interoperate with SFP-GIG-SX or similar transceiver on the other end
running over 850nm wavelength.

SFP-DUAL-SM10

- Dual Speed 100Base-FX or 1000Base-X Ethernet optical transceiver (SFP MSA).

Supports single mode fiber over 1310nm wavelength (nominal) with an LC connector. Typical reach of
10km at Gigabit speed and 100Mbit speed.

Note:

•

at 100Mbit speed, this SFP can interoperate with SFP-100-LC-SM15 or similar transceiver.

•

at Gigabit speed, this SFP can interoperate with SFP-GIG-LX or similar transceiver.

«
...
5
6
7
8
9
...
»

Содержание OmniSwitch 6800























































































Отзывы:

Нет отзывов

Похожие инструкции для OmniSwitch 6800

D DGS-3048 DGS-3048

Бренд: D-Link Страницы: 3

Бренд: Qlogic Страницы: 124

SANbox 5800V Series

Бренд: Qlogic Страницы: 158

Бренд: Qlogic Страницы: 324

SANbox 5600 Series

Бренд: Qlogic Страницы: 8

SANbox 5600 Series

Бренд: Qlogic Страницы: 10

SANbox 5200 Series

Бренд: Qlogic Страницы: 2

Бренд: Qlogic Страницы: 92

Бренд: Qlogic Страницы: 142

Бренд: Qlogic Страницы: 2

SANbox 1400 Series

Бренд: Qlogic Страницы: 2

QLogic Fibre Channel Switch

Бренд: Qlogic Страницы: 8

SANbox 5000 Series

Бренд: Qlogic Страницы: 350

SANbox 5000 Series

Бренд: Qlogic Страницы: 130

QLogic 12000 Series

Бренд: Qlogic Страницы: 144

Бренд: HPM Страницы: 4

Бренд: Cross Technologies Страницы: 20

ETHERNET Accessories 852 852-0111

Бренд: WAGO Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды