Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 444

background image

Configuration Process Overview

Page 96

7750 SR OS Interface Configuration Guide

Configuration Notes

The following information describes provisioning caveats:

•

Chassis slots must be preprovisioned to accept specific line card types.

•

Line cards must be preprovisioned to accept specific MDA types.

If a card or MDA type is installed in a slot provisioned for a different type, the card will
not initialize.

•

A card and MDA installed in an unprovisioned slot remain administratively and
operationally down until the slot, card type, MDA slot, and MDA type is specified.

•

Ports cannot be provisioned until the slot, card and MDA type are specified.

•

cHDLC does not support HDLC windowing features, nor other HDLC frame types such
as S-frames.

•

cHDLC operates in the HDLC Asynchronous Balanced Mode (ABM) of operation.

•

All SAP-level statistics are retained with an APS switch. A SAP will reflect the data
received regardless of the number of APS switches that has occurred. ATM statistics,
however, are cleared after an APS switch. Thus, any ATM statistics viewed on an APS
port are only the statistics since the current active member port became active.

Physical layer packet statistics on the APS group reflect what is currently on the active
member port.

•

Port and path-level statistics follow the same behavior.

Any SONET physical-layer statistics (for example, B1,B2,B3,...) on the APS port are only
what is current on the active APS member port.

•

APS configuration rules:

→

A physical port (either working or protection) must be shutdown before
it can be removed from an APS group port.

→

For a single-chassis APS group, a working port must be added first. Then a protection
port can be added or removed at any time.

→

A protection port must be shutdown before being removed from an APS group.

→

A path cannot be configured on a port before the port is added to an APS group.

→

A working port cannot be removed from an APS group until the APS port path is
removed.

→

When ports are added to an APS group, all path-level configurations are available
only on the APS port level and configuration on the physical member ports are
blocked.

→

For APS-protected bundles, all members of a working bundle must reside on the
working port of an APS group. Similarly all members of a protecting bundle must
reside on the protecting circuit of that APS group.

«
...
94
95
96
97
98
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 2

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 28

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 2

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Бренд: C&H Technologies Страницы: 46

Бренд: Ruckus Wireless Страницы: 56

Бренд: Idis Страницы: 31

Бренд: Keithley Страницы: 98

Бренд: CELOT Страницы: 34

Бренд: Accton Technology Страницы: 78

Бренд: Maipu Страницы: 19

Бренд: INNOSILICON Страницы: 11

Wisenet PRN-6400DB4

Бренд: Hanwha Techwin Страницы: 125

NetVanta 300 Series

Бренд: ADTRAN Страницы: 2

Бренд: qpcom Страницы: 4

Бренд: Tripp Lite Страницы: 2

Бренд: Tripp Lite Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды