Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 405

Страница: 405 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 405

Multilink-Bundle Relations Output Fields

Sample Output

A:ALA-48>show# show multilink-bundle bundle-ima-1/1.2 relations

==============================================================================

Bundle Relationship

==============================================================================

Bundle Admin Oper Working Protect Active

Id State State Bundle Id Bundle Id Bundle

------------------------------------------------------------------------------

bpgrp-ima-1 Down Down bundle-ima-1/1.1 bundle-ima-1/1.2 Protect

------------------------------------------------------------------------------

Bundles : 1

==============================================================================

A:ALA-48>show#

ima

Syntax

multilink-bundle ima

Context

show>multilink-bundle

Description

This command enables the context to display IMA group data.

MDA Values

1, 2

Output

Show Mutlilink-bundle IMA Connections Output —

The following table describes show

multilink-bundle IMA output fields.

Label

Description

BundleID

Displays the bundle number.

Admin State

Up —

The bundle is administratively up.

Down —

The bundle is administratively down.

Oper State

Up —

The bundle is operationally up.

Down —

The bundle is operationally down.

Working BundleID

Displays the bundle that is currently in working mode.

Protect BundleID

Displays the bundle that is currently in protect mode.

Active Bundle

Displays the mode of the active bundle.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды