Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 386

Страница: 386 / 444

Show Commands

Page 386

7750 SR OS Interface Configuration Guide

656441730 DS1, 14

656441755 DS1, 15

656441780 DS1, 16

656441805 DS1, 17

656441830 DS1, 18

656441855 DS1, 19

656441880 DS1, 20

656441905 DS1, 21

656441930 DS1, 22

656441980 DS1, 24

656442005 DS1, 25

656442030 DS1, 26

656442055 DS1, 27

656442080 DS1, 28

A:ALA-48>config#

redundancy

Syntax

redundancy

Context

show

Description

This command enables the context to show multi-chassis redundancy information.

multi-chassis

Syntax

multi-chassis all
mult-chassis mc-lag peer

ip-address

[

lag

lag-id

]

mult-chassis mc-lag

[

peer

ip-address

[

lag

lag-id

]]

statistics

mult-chassis sync

[

peer

ip-address

] [

detail

]

mult-chassis sync

[

peer

ip-address

]

statistics

Context

show>redundancy

Description

This command displays multi-chassis redundancy information.

Parameters

all —

Displays all multi-chassis information.

mc-lag —

Displays multi-chassis LAG information.

peer

ip-address

—

Displays the address of the multi-chassis peer.

lag

lag-id

—

Displays the specified LAG ID on this system that forms an multi-chassis LAG

configuration with the indicated peer.

statistics —

Displays statistics for the multi-chassis peer.

sync —

Displays synchronization information.

detail —

Displays detailed information.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 386 / 444

Результаты поиска

Содержание 7750 SR OS

Отзывы: