Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 336

Страница: 336 / 444

Show Commands

Page 336

7750 SR OS Interface Configuration Guide

APS Show Commands

aps

Syntax

aps

[

aps-id

] [

detail

]

Context

show

Description

This command displays Automated Protection Switching (APS) information.

Parameters

aps-id —

Displays information for the specified APS group ID.

Values

aps-

group-id

aps:

keyword

group-id

: 1 — 128

detail —

Displays detailed APS information.

Output

APS Output —

The following table describes APS output fields.

Label

Description

Interface

Specifies the APS interface name (the APS group port).

Admin State

Up —

APS is administratively up.

Down —

APS port is administratively down.

Oper State

Up —

APS port is operationally up.

Down —

APS is operationally down.

MC-CTL State

Specifies the multi-chassis state.

Work Circuit

Specifies the working circuit ID.

Prot Circuit

Specifies the physical port that acts as the protection circuit for this
APS group.

Active Circuit

Specifies the active circuit.

Tx/Rx K1 Byte

Displays the value of the SONET/SDH K1 byte received or transmitted
on the protection circuit.

Group Id

Displays the APS group name.

Protection Cir-

cuit

Displays the physical port that will act as the protection circuit for this
APS group.

Switching-mode

Displays the switching mode.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды