Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 307 | Manualshive

Страница: 307 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 307

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 307

Parameters

ip-address —

Specifies the destination IP address.

interface

Syntax

interface

ip-int-name

no interface

Context

config>redundancy>mc>peer>mcr>ring>in-band-control-path

Description

This command specifies the name of the IP interface used for the inband control connection. If the
name is not configured, the ring cannot become operational.

service-id

Syntax

service-id

service-id

no service-id

Context

config>redundancy>mc>peer>mcr>ring>ibc
config>redundancy>mc>peer>mcr>node>cv

Description

This command specifies the service ID if the interface used for the inband control connection belongs
to a VPRN service. If not specified, the

service-id

is zero and the interface must belong to the Base

router.

The

no

form of the command removes the service-id from the IBC configuration.

Parameters

service-id —

Specifies the service ID if the interface.

path-b

Syntax

[

no

]

path-b

Context

config>redundancy>mc>peer>mcr>ring

Description

This command specifies the set of upper-VLAN IDs associated with the SAPs that belong to path B
with respect to load-sharing. All other SAPs belong to path A.

Default

If not specified, the default is an empty set.

«
...
305
306
307
308
309
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов