Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 296

Страница: 296 / 444

Configuration Commands

Page 296

7750 SR OS Interface Configuration Guide

Parameters

slow —

Transmits packets every 30 seconds.

fast —

Transmits packets every second.

lacp-xmit-stdby

Syntax

[

]

lacp-xmit-stdby

Context

config>lag

Description

This command enables LACP message transmission on standby links.

The

form of this command disables LACP message transmission. This command should be

disabled for compatibility when using active/standby groups. This forces a timeout of the standby
links by the peer. Use the

form if the peer does not implement the correct behavior regarding the

lacp sync bit.

Default

lacp-xmit-stdby

mode

Syntax

mode

{

access

network

}

no mode

Context

config>lag

Description

This command configures the mode of the Link Aggregation Group (LAG).

Parameters

access —

Configures the mode as access for the LAG.

network —

Configures the mode as network for the LAG.

port

Syntax

port

port-id

[

port-id

…

up to 8 total] [

priority

priority

] [

subgroup

sub-group-id

]

no port

port-id

[

port-id

…

up to 8 total]

Context

config>lag

lag-id

Description

This command adds ports to a Link Aggregation Group (LAG).

The port configuration of the first port added to the LAG is used as a basis to compare to
subsequently added ports. If a discrepancy is found with a newly added port, that port will be not
added to the LAG.

Up to eight (space separated) ports can be added or removed from the LAG link assuming the
maximum of 8 ports is not exceeded.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 296 / 444

Результаты поиска

Содержание 7750 SR OS

Отзывы: