manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 291 / 444

Поделиться
Скачать
Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 291

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 291

The 

no

 form of this command reverts to the default value.

Default

threshold ber-sd rate 5 
threshold ber-sf rate 50

Parameters

ber-sd — 

Specifies the BER that specifies signal degradation.

ber-sf — 

Specifies the BER that specifies signal failure.

rate — 

Specifies the number of errors, in millions.

timeslots

Syntax

timeslots 

timeslots

no timeslots

Context

config>port>tdm>ds1>channel-group
config>port>tdm>e1>channel-group

Description

This command defines the list of DS-0 timeslots to be used in the DS-1/E-1 channel-group. The 
timeslots are defaulted as defined below when encap-type is set to/from atm. ATM channel groups do 
not allow timeslots to change.

The 

no

 form of this command removes DS-0 timeslots from a channel group.

Default

no timeslots — Non-ATM channel groups.
1-24  — Channel groups configured under DS-1 with encap set to ATM.
2-16,18-32 — Channel groups configured under E-1 with encap set to ATM.

Parameters

timeslots  — 

Specifies the timeslot(s) to be associated with the channel group.  The value can consist 

of a list of timeslots. Each member of the list can either be a single timeslot or a range of 
timeslots.

Values

1 — 24 for DS-1 interfaces (the full range is auto-configured for ATM channel 
groups and cannot be changed).
2 — 32 for E-1 interfaces (the 2 — 16,18 — 32 ranges are auto-configured for 
ATM channel groups and cannot be changed).

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов