Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 288

Страница: 288 / 444

Configuration Commands

Page 288

7750 SR OS Interface Configuration Guide

This command is only applicable if the DS-3/E-3 is using C-bit framing (see the

framing (DS3)

command).

The

form of this command removes the MDL string association and stops the transmission of any

IDs.

Default

no mdl

Parameters

mdl-string —

specify an MDL message up to 38 characters long on a DS-3.

eic —

Specifies the equipment ID code up to 10 characters long.

lic —

Specifies the equipment ID code up to 11 characters long.

fic —

Specifies the ID code up to 10 characters long.

unit —

Specifies the unit ID code up to 6 characters long.

pfi —

Specifies the facility ID code up to 38 characters long.

port —

Specifies the port ID code up to 38 characters long.

gen —

Specifies the generator number to send in the MDL test signal message up to 38 characters

long.

mdl-transmit

Syntax

mdl-transmit

{

path

idle-signal

test-signal

}

no mdl-transmit

[

path

idle-signal

test-signal

]

Context

config>port>tdm>ds3
config>port>tdm>e3

Description

This command enables the transmission of an MDL message on a DS-3/E-3 over channelized
interface.

The

form of this command disables transmission of the specified message or all messages.

Default

no mdl-transmit

Parameters

path —

Specify the MDL path message.

idle-signal —

Specify the MDL idle signal message.

test-signal —

Specify the MDL test signal message.

remote-loop-respond

Syntax

[

]

remote-loop-respond

Context

config>port>tdm>ds1

Description

When abled, the channel responds to requests for remote loopbacks.

Default

no remote-loop-respond — The port will not respond.

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды