Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 285 | Manualshive

Страница: 285 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 285

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 285

config>port>tdm>e1
config>port>tdm>e1>channel-group
config>port>tdm>e3

Description

This command configures the value that the HDLC TDM DS-0, E-1, E-3, DS-1, or DS-3 interface
transmits during idle cycles. For ATM ports/channels/channel-groups, the configuration does not
apply and only the no form is accepted.

The

no

form of this command reverts the idle cycle flag to the default value.

Default

flags (0x7E)

no flags (ATM)

Parameters

flags —

Specifies that 0x7E is used as the idle cycle flag.

ones —

Specifies that 0xFF is used as the idle cycle flag.

idle-payload-fill

Syntax

idle-payload-fill

{

all-ones

}

idle-payload-fill pattern

pattern

no idle-payload-fill

Context

config>port>tdm>ds1>channel-group
config>port>tdm>e1>channel-group

Description

This command defines the data pattern to be transmitted when the circuit emulation service is not
operational or temporarily experiences under-run conditions. This command is only valid for cesopsn
and cesopsn-cas circuit emulation services. It is blocked with a warning for unstructured (satop)
circuit emulation services.

Default

all-ones

Parameters

all-ones —

Defines the 8 bit value to be transmitted as 11111111.

pattern —

Transmits a user-defined pattern.

idle-signal-fill

Syntax

idle-signal-fill

{

all-ones

}

idle-signal-fill pattern

pattern

no idle-signal-fill

Context

config>port>tdm>ds1>channel-group
config>port>tdm>e1>channel-group

Description

This command defines the signaling pattern to be transmitted when the circuit emulation service is
not operational or temporarily experiences under-run conditions. This command is only valid for
cesopsn-cas circuit emulation services. It is blocked with a warning for unstructured (satop) and basic
cesopsn circuit emulation services.

«
...
283
284
285
286
287
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов