Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 274 | Manualshive

Страница: 274 / 444

background image

Configuration Commands

Page 274

7750 SR OS Interface Configuration Guide

TDM Commands

tdm

Syntax

tdm

Context

config>port

Description

This command enables the context to configure DS-1/E-1 and DS-3/E-3 parameters for a port on a
channelized MDA. This context cannot be accessed on non-channelized MDAs.

TDM is a mechanism to divide the bandwidth of a stream into separate channels or time slots by
assigning each stream a different time slot in a set. TDM repeatedly transmits a fixed sequence of
time slots over a single transmission channel. Each individual data stream is reassembled at the
receiving end based on the timing.

Default

None

ds1

Syntax

[

no

]

ds1

ds1-id

Context

config>port>tdm

Description

This command enables the context to configure digital signal level 1 (DS-1) frame parameters. The
T-Carrier system was the first successful system that supported digitized voice transmission. The
original transmission rate (1.544 Mbps) in the T-1 (DS-1) line is commonly used by Internet service
providers (ISPs) to connect to the Internet.

North America uses the T-Carrier system while Europe uses the E-Carrier system of transmission,
using multiples of the DS- system. Digital signals are carried inside the carrier systems.

T-1 transmits DS-1-formatted data at 1.544 Mbps through the network. The corresponding European
carrier is E-1 with a data rate of 2.048 Mbps. E-1 and T-1 (DS-1) can be interconnected for interna-
tional use.

The

no

form of this command disables DS-1 capabilities.

Default

None

Parameters

ds1-id —

Identifies the DS-1 channel being created.

Values

DS1: 1 — 28

«
...
272
273
274
275
276
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

IntelliJack NJ200

Бренд: 3Com Страницы: 4

IES615-2D Series

Бренд: 3onedata Страницы: 3

Бренд: 3One data Страницы: 5

Бренд: 3onedata Страницы: 33

Бренд: Lanpro Страницы: 5

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

Бренд: Paradyne Страницы: 32

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

FrameSaver 9783

Бренд: Paradyne Страницы: 28

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 7

NetVanta 6355 PoE

Бренд: ADTRAN Страницы: 46

Бренд: Juniper Страницы: 825

Бренд: SAGEMCOM Страницы: 75

Бренд: 4G Systems Страницы: 2

Бренд: TP-Link Страницы: 87

Бренд: X-Micro Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды