Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 266 | Manualshive

Страница: 266 / 444

background image

Configuration Commands

Page 266

7750 SR OS Interface Configuration Guide

min-vp-vpi

Syntax

min-vp-vpi

value

Context

config>port>sonet-sdh>path>atm
config>port>multilink-bundle>ima>atm
config>port>tdm>ds1>channel-group>atm
config>port>tdm>ds3>atm
config>port>tdm>e1>channel-group>atm
config>port>tdm>e3>atm

Description

This command sets the minimum allowable virtual path identifier (VPI) value that can be used on the
ATM interface for a VPC.

Parameters

value —

Specify the minimum allowable VPI value that can be used on the ATM interface for a VPC.

Values

0 — 4095 (NNI)
0 — 255 (UNI)

Default

0

ilmi

Syntax

ilmi

[

vpi/vci

]

no ilmi

Context

config>port>sonet-sdh>path>atm

Description

This command creates an ILMI link PVCC by default on VPI/VCI 0/16. Deleting an ILMI link
deletes the PVCC. ILMI is supported only on ATM interfaces on SONET/SDH paths.

Parameters

vpi/vci —

Specifies the PVC identifier (vpi/vci).

Values

vpi

0 — 4095 (NNI)
0 — 255 (UNI)

vci

1, 2, 5 — 65535

egress

Syntax

egress

Context

config>port>sonet-sdh>path>atm>ilmi

Description

This command enables the context to configure egress traffic attributes for the ILMI link.

«
...
264
265
266
267
268
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Бренд: PaloAlto Networks Страницы: 3

Бренд: Watchguard Страницы: 40

Бренд: SAGEMCOM Страницы: 75

LBON320AC Series

Бренд: Lindsay Broadband Страницы: 4

Бренд: Abocom Страницы: 63

Бренд: StarTech.com Страницы: 9

Sinus 154 data II

Бренд: T-COM Страницы: 12

Бренд: F.F. Group Страницы: 56

Бренд: Raven Страницы: 33

Бренд: LUX LUMEN Страницы: 41

WebShare 141 WN

Бренд: Atlantis Страницы: 78

Бренд: l-com Страницы: 2

Бренд: Alloy Страницы: 13

Бренд: Sarian Systems Страницы: 9

Бренд: Epson Страницы: 71

Бренд: Epson Страницы: 29

Бренд: Epson Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды