Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 260 | Manualshive

Страница: 260 / 444

background image

Configuration Commands

Page 260

7750 SR OS Interface Configuration Guide

plcd —

Reports path loss of codegroup delineation errors. It is applicable only when the value of

xgig is set to WAN.

Default

plcd

traps are not issued

crc

Syntax

crc

{

16

|

32

}

Context

config>port>sonet-sdh>path

Description

A 16 bit CRC can only be configured on an OC-3 channel, all other channel speeds must use a 32 bit
CRC except for the paths configured with encap-type atm at OC3 speed.

Default

16 for OC-3, DS-1, DS-3
32 for OC-12, OC-48, ATM-OC12/3, ATMOC-3, etc.

Note: The CRC default is 32 when the encap-type is set to ATM and also, the default cannot be
changed when the encap-type is set to ATM.

Parameters

16 —

Use 16 bit checksum for the associated port/channel.

32 —

Use 32 bit checksum for the associated port/channel.

encap-type

Syntax

encap-type

{

atm

|

bcp-null

|

bcp-dot1q

|

ipcp

|

ppp-auto

|

frame-relay

|

wan-mirror

|

cisco-hdlc

}

Context

config>port>sonet-sdh>path

Description

This command configures the encapsulation method used to distinguish customer traffic on an access
SONET/SDH channel sub-port.

When the

encap-type

is set to ATM the CRC default cannot be changed.

When the

encap-type

is ATM, ATM sub-layer verification (GR-1248-CORE,

Generic Requirements

for Operations of ATM Network Elements (NEs)

) is automatically enabled. The result of the

verification includes:

• Out of Cell Delineation (OCD) event count. The OCD event count is described in RFC 2515,

Definitions of Managed Objects for ATM Management

. Note that multiple events occurring

within a second will be counted as 1 event for ATM and ASAP MDAs as a result of a hardware
limit.

• Loss of Cell Delineation defect/alarm. The LCD defect/alarm is defined in RFC 2515,

Defini-

tions of Managed Objects for ATM Management

. When a path is in an LCD defect state, the

path’s operational status will be down. When a path exits the LCD state, the path’s operational
status will change to up (assuming nothing else causes the path to stay down). A trap is raised to
indicate the LCD status change. Also a P-RDI is sent to indicate the defect to the remote end.

The

encap-type

is only required when configuring a SONET/SDH path for access mode.

«
...
258
259
260
261
262
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: M2M Страницы: 9

Бренд: Paradyne Страницы: 2

Бренд: QNAP Страницы: 39

Бренд: IEI Technology Страницы: 86

Lite N42B1P Series

Бренд: Dahua Technology Страницы: 14

Dimension ES-3124

Бренд: ZyXEL Communications Страницы: 228

Бренд: Tbus Страницы: 25

Бренд: Faderfox Страницы: 10

PG-Flex FLC-704

Бренд: PairGain Страницы: 20

CloudGen Firewall

Бренд: Barracuda Страницы: 8

Бренд: Maestro Wireless Solution Страницы: 22

Бренд: M86 Security Страницы: 540

Бренд: XtendLan Страницы: 54

Бренд: Matrix Switch Corporation Страницы: 48

Бренд: Avaya Страницы: 2

Бренд: 3Com Страницы: 17

Бренд: H3C Страницы: 46

Бренд: Cambium Networks Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды