Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 258 | Manualshive

Страница: 258 / 444

background image

Configuration Commands

Page 258

7750 SR OS Interface Configuration Guide

SONET/SDH Path Commands

path

Syntax

[

no

]

path

[

sonet-sdh-index

]

Context

config>port>sonet-sdh

Description

This command defines the SONET/SDH path.

The

no

form of this command removes the specified SONET/SDH path.

Default

full channel (or clear channel)

Parameters

sonet-sdh-index —

Specifies the components making up the specified SONET/SDH path. Depending

on the type of SONET/SDH port the

sonet-sdh-index

must specify more path indexes to specify

the payload location of the path. The

sonet-sdh-index

differs for SONET and SDH ports.

Syntax

: sts1-

x

.

x

In addition the support of virtual tributary circuits adds an additional level of complexity and several
addition levels of indexes.

payload

Syntax

payload

{

sts3

|

tug3

|

ds3

|

e3

}

Context

config>port>sonet-sdh>path

Description

This command specifies if the associated SONET/SDH path is an asynchronous circuit or a virtual
tributary group (VT). This command is only applicable to channelized MDAs.

SONET

SDH

OC-192

STS-48-index
STS-12-index
STS-3-index
STS-1-index

STM-64

AUG-16-index
AUG-4-index
AUG-1-index
AU-3-index

OC-48 STS-12-index

STS-3-index
STS-1-index

STM-16 AUG-4-index

AUG-1-index
AU-3-index

OC-12

STS-3-index
STS-1-index

STM-4

AUG-1-index
AU-3-index

OC-3

STS-1-index

STM-1

AU-3-index

«
...
256
257
258
259
260
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: GE Страницы: 6

Бренд: Rain Bird Страницы: 17

Бренд: Hama Страницы: 10

Бренд: NETGEAR Страницы: 169

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

TRAK 2OP M11 Mill

Бренд: XYZ Machine Tools Страницы: 203

Бренд: Moxa Technologies Страницы: 51

Бренд: Zalip Страницы: 77

EtherFast LNE100TX ver. 5

Бренд: Linksys Страницы: 42

Бренд: UTStarcom Страницы: 71

Бренд: Airlink101 Страницы: 46

Бренд: TP-Link Страницы: 37

Бренд: BinTec Страницы: 34

Бренд: ActionTec Страницы: 87

Бренд: Divio Страницы: 78

ICPE2600 Series

Бренд: 3onedata Страницы: 5

Бренд: TP-Link Страницы: 2

Бренд: LOOQS Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды