Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 253 | Manualshive

Страница: 253 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 253

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 253

framing

Syntax

framing

{

sonet

|

sdh

}

Context

config>port>sonet-sdh

Description

This command specifies SONET/SDH framing to be either SONET or SDH.

Default

sonet

Parameters

sonet —

Configures the port for SONET framing.

sdh —

Configures the port for SDH framing.

group

Syntax

group

sonet-sdh-index

payload

{

tu3

|

vt2

|

vt15

}

Context

config>port>sonet-sdh

Description

This command configures payload of the SONET/SDH group.

For example:

config>port>sonet-sdh#

group tug3-1.1 payload tu3
group tug3-1.2 payload vt2
group tug3-1.3 payload vt2
group tug3-2.1 payload vt15
group tug3-2.2 payload vt15
group tug3-2.3 payload tu3
group tug3-3.1 payload tu3
group tug3-3.2 payload tu3
group tug3-3.3 payload tu3

Default

none

Parameters

sonet-sdh-index —

Specifies the components making up the specified SONET/SDH path. Depending

on the type of SONET/SDH port the

sonet-sdh-index

must specify more path indexes to specify

the payload location of the path.

tu3 —

Specify the Tributary Unit Group (TUG3) on a path. Configures the port or channel for

transport network use.

vt2 —

Configures the path as a virtual tributary group of type vt2.

vt15 —

Configures the path as a virtual tributary group of type vt15.

«
...
251
252
253
254
255
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов