Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 252 | Manualshive

Страница: 252 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 252

Configuration Commands

Page 252

7750 SR OS Interface Configuration Guide

SONET/SDH Port Commands

sonet-sdh

Syntax

sonet-sdh

Context

config>port

Description

This command enables access to the context to configure SONET/SDH ports. This context can only
be used when configuring an OC-3, OC-12, OC-48 and OC-192 SONET/SDH ports on an
appropriate MDA.

The 10 Gigabit Ethernet LAN port also has SONET/SDH characteristics. However, these
characteristics are predetermined and not configurable.

clock-source

Syntax

clock-source

{

loop-timed | node-timed

}

Context

config>port>sonet-sdh

Description

This command configures the clock for transmitted data from either the internal clock or from a clock
recovered from the line’s receive data stream.

Note: When changing the clock source for a port on an OC-48 MDA, a brief transmit interruption can
occur on all ports of that MDA. The following table show MDAs that support loop timing:

Parameters

loop-timed —

The link recovers the clock from the received data stream.

node-timed —

The link uses the internal clock when transmitting data.

MDA Supports

Loop Timed

Default

OC-192

Yes

loop-timed

OC-48

Yes

loop-timed

OC-12 No

node-timed

OC-3 No

node-timed

Channelized OC-12

Yes

loop-timed

Channelized OC-3

Yes

loop-timed

Channelized DS-3

Yes

loop-timed

Channelized ASAP

Yes

loop-timed

Channelized ASAP

Yes

loop-timed

«
...
250
251
252
253
254
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов