Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 248 | Manualshive

Страница: 248 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 248

Configuration Commands

Page 248

7750 SR OS Interface Configuration Guide

yellow-differential-delay

Syntax

yellow-differential-delay

yellow-diff-delay

no yellow-differential-delay

Context

config>port>multilink-bundle

Description

This command sets the yellow warning threshold for the differential delay for members within a
multilink bundle. If circuit’s delay exceeds the yellow-differential delay value, a log message and
SNMP trap is sent. This command is only valid for MLPPP bundles. The differential delay is
calculated as the round-trip differential delay for MLPPP bundles.

The no form of this command removes the yellow-differential-delay.

The

no

form of this command removes the yellow-differential-delay.

Default

None

Parameters

yellow-diff-delay —

Specify the maximum yellow differential delay threshold value.

Values

1— 25 milliseconds

ima

Syntax

ima

Context

config>port>multilink-bundle

Description

This command enables the context to configure parameters for an Inverse Multiplexing over ATM
(IMA) group. An IMA group is a collection of physical links bundled together and assigned to an
ATM interface. IMA enables a high-speed channel that is composed of ATM cells to be transported as
a number of lower-speed circuits. Then they are reassembled as the original high-speed ATM
channel. This command is only valid for IMA bundles.

link-delay

Syntax

link-delay

{

activate

|

deactivate

}

milli-seconds

no link-delay

{

activate

|

deactivate

}

Context

config>port>multilink-bundle>ima

Description

This command specifies the time to delay between detection of a link activation/deactivation
condition and acting upon it (going in/out of the RX failure state on a link).

Parameters

activate

milli-seconds

—

Specifies the time, in milli-seconds, used to clear an existing LIF or LODS

alarm. The time specified determines how long is needed for member links to stabilize before
being activated.

Values

1 — 30000 milli-seconds

Default

10000

«
...
246
247
248
249
250
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов