Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 231 | Manualshive

Страница: 231 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 231

ingress-rate

Syntax

ingress-rate

sub-rate

no ingress-rate

Context

config>port>ethernet

Description

This command configures the maximum amount of ingress bandwidth that this port can receive.

The ingress-rate command is only valid for oversubscribed Ethernet MDAs. See

Oversubscribed

Ethernet MDAs on page 21

for details.

The

no

form of this command returns the value to the default.

Default

no ingress-rate

Parameters

sub-rate —

The egress rate in mbps.

Values

1 — 10000 mbps

lacp-tunnel

Syntax

[

no

]

lacp-tunnel

Context

config>port>ethernet

Description

This command enables LACP packet tunneling for the Ethernet port. When tunneling is enabled, the
port will not process any LACP packets but will tunnel them instead. The port cannot be added as a
member to a LAG group.

The

no

form of the command disables LACP packet tunneling for the Ethernet port.

Default

no lacp-tunnel

load-balancing-algorithm

Syntax

load-balancing-algorithm

option

no load-balancing-algorithm

Context

config>port>ethernet
config>port>sonet-sdh>path
config>port>tdm>ds1>channel-group
config>port>tdm>ds3
config>port>tdm>e1>channel-group
config>port>tdm>e3

Description

This command specifies the load balancing algorithm to be used on this port.

In the default mode,

no load-balancing-algorithm

, the port inherits the global settings. The value is

not applicable for ports that do not pass any traffic.

The configuration of load-balancing-algorithm at logical port level has three possible values:

«
...
229
230
231
232
233
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 8

AirPlus DWL-810

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 84

TotalStorage SAN16M-R SAN

Бренд: IBM Страницы: 116

TOWERCHRON DP72

Бренд: Grasslin Страницы: 2

Бренд: TP-Link Страницы: 2

Бренд: Xantech Страницы: 4

E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010

Бренд: Juniper Страницы: 122

NOVA300 AML02304U1

Бренд: Nexxt Страницы: 75

Бренд: FOR-A Страницы: 2

EtherLink 3C905C-TX

Бренд: 3Com Страницы: 96

Бренд: Intercoax Страницы: 2

Бренд: Teldat Страницы: 23

Бренд: Ubiquiti Страницы: 20

Xtreme Networked Boat

Бренд: Broadband Products Страницы: 16

Бренд: Tripp Lite Страницы: 2

Бренд: bintec elmeg Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды