Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 216 | Manualshive

Страница: 216 / 444

background image

Configuration Commands

Page 216

7750 SR OS Interface Configuration Guide

APS Commands

aps

Syntax

aps

Context

config>port

Description

This command configures APS (Automatic Protection Switching). APS is used by SONET/SDH add/
drop multiplexers (ADMs) or other SONET/SDH-capable equipment to protect against circuit or
equipment failure.

When configuring APS to protect against media or port failure, both working and protection circuits
must be configured on the same node with the same

aps

-

group-id

.

The working and protection configurations on Alcatel-Lucent 7750 SRs must match the circuit
configurations on the peer. This means that the working circuit on the 7750 SR must be connected to
the peer’s working circuit and the protect circuit must be connected to the peer’s protection circuit.

The

aps

command is only available for APS groups and not physical ports.

Default

none

advertise-interval

Syntax

advertise-interval

advertise-interval

no advertise-interval

Context

config>port>aps

Description

This command specifies the time interval, in 100s of milliseconds, between 'I am operational'
messages sent by both protect and working circuits to their neighbor for multi-chassis APS.

The

advertise-interval

value is valid only for a multi-chassis APS as indicated by the value of the

neighbor

command value if it is not set to 0.0.0.0.

Default

10

Parameters

advertise-interval —

Specifies the time interval, in 100s of milliseconds, between 'I am operational'

messages sent by both protect and working circuits to their neighbor for multi-chassis APS.

Values

10 — 650

«
...
214
215
216
217
218
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

BB-HGW700A - Network Camera Router

Бренд: Panasonic Страницы: 10

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Zhone Страницы: 2

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 155

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 44

LightSpeed Appliance QLS250

Бренд: Quantum Страницы: 12

Бренд: Ruckus Wireless Страницы: 102

AT-9424Ts/XP AC

Бренд: Allied Telesis Страницы: 3

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

Бренд: ZyXEL Communications Страницы: 116

Бренд: Patton electronics Страницы: 9

Бренд: Qlogic Страницы: 8

Бренд: Gira Страницы: 6

Бренд: Patton electronics Страницы: 2

Бренд: TP-Link Страницы: 57

Бренд: Dataprobe Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды