Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 201 | Manualshive

Страница: 201 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 201

Description

This command specifies the network-queue policy which defines queue parameters such as CBS,
high priority only burst size, MBS, CIR and PIR rates, as well as forwarding-class to queue
mappings. The network-queue policy is defined in the

config>qos>network-queue

context.

Default

default

Parameters

name —

Specifies an exisiting network-queue policy name.

resv-cbs

Syntax

resv-cbs

percent-or-default

no resv-cbs

Context

config>card>mda>access>egress
config>card>mda>access>ingress
config>card>mda>network>egress
config>card>mda>network>ingress
config>port>access>egress>pool
config>port>access>egress>channel>pool
config>port>access>ingress>pool
config>port>network>egress>pool

Description

This command defines the percentage or specifies the sum of the pool buffers that are used as a
guideline for CBS calculations for access and network ingress and egress queues. Two actions are
accomplished by this command.

• A reference point is established to compare the currently assigned (provisioned) total CBS with

the amount the buffer pool considers to be reserved. Based on the percentage of the pool reserved
that has been provisioned, the over provisioning factor can be calculated.

• The size of the shared portion of the buffer pool is indirectly established. The shared size is

important to the calculation of the instantaneous-shared-buffer-utilization and the average-
shared-buffer-utilization variables used in Random Early Detection (RED) per packet slope plot-
ting.

It is important to note that this command does not actually set aside buffers within the buffer pool for
CBS reservation. The CBS value per queue only determines the point at which enqueuing packets are
subject to a RED slope. Oversubscription of CBS could result in a queue operating within its CBS
size and still not able to enqueue a packet due to unavailable buffers. The resv-cbs parameter can be
changed at any time.

If the total pool size is 10 MB and the resv-cbs set to 5, the ’reserved size’ is 500 KB.

The

no

form of this command restores the default value.

Default

default (30%)

Parameters

percent-or-default —

Specifies the pool buffer size percentage.

Values

0 — 100, default

«
...
199
200
201
202
203
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Makita Страницы: 2

Бренд: Magnat Audio Страницы: 2

Бренд: NEC Страницы: 8

Бренд: Wave wifi Страницы: 2

Бренд: Obihai Страницы: 2

Adapter Bracket

Бренд: Paradyne Страницы: 1

Бренд: Conceptronic Страницы: 230

Бренд: H3C Страницы: 77

EonServ 5000 Series

Бренд: Surveon Страницы: 33

Бренд: Paradyne Страницы: 23

Vigor 2760 Series

Бренд: Draytek Страницы: 54

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Бренд: LaCie Страницы: 67

Бренд: Allied Telesis Страницы: 2

Бренд: Kentrox Страницы: 246

Бренд: ZyXEL Communications Страницы: 2

Бренд: Wave wifi Страницы: 3

Бренд: Vaisala Страницы: 32

Бренд: BinTec Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды