Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 444

background image

Configuration Commands

Page 186

7750 SR OS Interface Configuration Guide

Parameters

long-description-string —

The description character string. Strings can be up to 160 characters long

composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $,
spaces, etc.), the entire string must be enclosed within double quotes.

shutdown

Syntax

[

no

]

shutdown

Context

config>card
config>card>mda
config>port
config>port>sonet-sdh>path
config>port>tdm>ds1
config>port>tdm>ds1>channel-group
config>port>tdm>ds3
config>port>tdm>e1
config>port>tdm>e1>channel-group
config>port>tdm>e3
config>port>multilink-bundle>ima>test-pattern-procedure
config>port>sonet-sdh>path>atm>ilmi
config>lag
config>port>ethernet>efm-oam
config>redundancy>multi-chassis>peer
config>redundancy>mc>peer>mc-lag
config>redundancy>mc>peer>mcr>ring
config>redundancy>mc>peer>mcr>node>cv
config>redundancy>multi-chassis>peer>sync

Description

This command administratively disables an entity. When disabled, an entity does not change, reset, or
remove any configuration settings or statistics.

The operational state of the entity is disabled as well as the operational state of any entities contained
within.

The

no

form of this command administratively enables an entity.

Special Cases

card —

The default state for a card is

no shutdown

.

mda —

The default state for a mda is

no

shutdown

.

lag —

The default state for a Link Aggregation Group (LAG) is

shutdown

.

port —

The default state for a port is

shutdown

.

path —

The default state for a SONET/SDH path is

shutdown

.

«
...
184
185
186
187
188
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 4

Бренд: Variscite Страницы: 18

Бренд: UfiSpace Страницы: 32

Бренд: TRENDnet Страницы: 10

Бренд: Galaxy Страницы: 30

Бренд: Solwise Страницы: 7

Бренд: Zhone Страницы: 53

Бренд: Cradlepoint Страницы: 2

Бренд: Multi-Link Страницы: 31

Бренд: MicroNova Страницы: 113

Бренд: ADC Страницы: 29

Бренд: Intercel Страницы: 17

Бренд: LevelOne Страницы: 10

Бренд: Caimore Страницы: 79

Бренд: Supero Страницы: 66

Бренд: B&B Electronics Страницы: 74

Бренд: Xaptum Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды