Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 158

Service Management Tasks

Page 158

7750 SR OS Interface Configuration Guide

Soft IOM Reset

The soft IOM reset procedure is applicable during the ISSU process and for a manual soft reset
procedure. The impact to the data plane forwarding during the reboot process is minimized to ten
(10) seconds or less. When the control plane is rebooted, time sensitive tasks currently running on
the IOM need to be redirected to the CPM. The command to perform a soft IOM reset is “

clear

card

card-number

soft

”. During the process, related show commands such as “

show card

” and

“

show mda

” will indicate a soft IOM reset is occurring.

«
...
156
157
158
159
160
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов