Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 140

Страница: 140 / 444

Configuring Ports

Page 140

7750 SR OS Interface Configuration Guide

ATM Interface Configurations

Use the following CLI syntax to configure ATM interface parameters for SONET/SDH paths:

CLI Syntax:

config# port

port-id

sonet-sdh

path [

sonet-sdh-index

]

atm

cell-format

cell-format

ilmi [

vpi/vci

]

egress

traffic-desc t

raffic-desc-profile-id

ingress

traffic-desc

traffic-desc-profile-id

keep-alive [poll-frequency

seconds

] [poll-

count

value

] [test-frequency

seconds

]

protocol

protocol-type

[no] shutdown

min-vp-vpi

value

Use the following CLI syntax to configure ATM interface parameters for IMA bundles.

CLI Syntax:

config>port>multilink-bundle

ima

atm

cell-format

cell-format

min-vp-vpi

value

Use the following CLI syntax to configure ATM interface parameters for TDM channels:

CLI Syntax:

config# port {

port-id

}

tdm

ds1 [

ds1-id

]

channel-group 1

atm

cell-format

cell-format

min-vp-vpi

value

ds3 [

sonet-sdh-index

]

atm

cell-format

cell-format

min-vp-vpi

value

mapping {direct | plcp}

e1 [

e1-id

]

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды