Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 105

Страница: 105 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 105

Configuring Forwarding Plane Parameters

The following output provides a forwarding plane configuration. The

command is not allowed

on iom-1 or iom-2 types. An error message appears when the command is executed on an
incorrect IOM type:

MINOR: CLI This command is not supported for iom2-20g.

*A:Dut-C# configure card 10

*A:Dut-C>config>card# info

----------------------------------------------

card-type iom3-xp

fp 1

ingress

mcast-path-management

bandwidth-policy "BWP"

no shutdown

exit

mda 1

mda-type m1-10gb

ingress

mcast-path-management

bandwidth-policy "BWP"

no shutdown

exit

mda 2

mda-type m2-10gb-xfp

ingress

mcast-path-management

bandwidth-policy "BWP"

no shutdown

exit

----------------------------------------------

*A:Dut-C>config>card# exit

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса, Страница: 105 / 444

Результаты поиска

Содержание 7750 SR OS

Отзывы: