Alaxala AX3630S Скачать руководство пользователя страница 853 | Manualshive

Страница: 853 / 875

background image

40. Error Messages Displayed When Editing the Configuration

825

40.1.15 Access list information

Table 40-15:

Access list error messages

Cannot change the flow action-change cos.

The priority determination operation cannot be changed because QoS flow

detection conditions and operation information entries are applied to the

interface.
To change the priority determination operation, delete all QoS flow

detection conditions and operation information entries applied to the
interface.
Note that you can use the

show system

operation command to check the

number of QoS entries used by this configuration file.

Cannot change the configuration because

there is an inconsistency between flow
detection mode and policy based routing.

A conflict occurred between the policy-based routing setting and the flow

detection mode setting.
To apply policy-based routing, set the flow detection mode to

layer3-6

.

To set the flow detection mode to other than

layer3-6

, delete the

policy-list

and

policy-list default-init-interval

command

settings.

Cannot change the flow detection mode.

The flow detection mode cannot be changed because an access list or a QoS

flow list is applied to the interface.

•

For AX3640S series switches:
To change the flow detection mode, delete all the lists that are applied

to the receiving-side interface and the sending-side interface.

•

For AX3630S series switches:
To change the flow detection mode, delete all the lists that are applied

to the receiving-side interface.

Cannot change the flow detection out mode.

The sending-side flow detection mode cannot be changed because an access
list is applied to the interface.
To change the sending-side flow detection mode, delete all access lists that
are applied to the receiving-side interface and the sending-side interface.

Relations between flow detection out mode

layer3-3-out and dot1q-tunnel are
inconsistent.

layer3-3-out cannot be specified for the sending-side flow detection mode

because a tunneling port is set on the Switch.
A tunneling port cannot be set if layer3-3-out is specified for the

sending-side flow detection mode.
Delete the tunneling port setting, specify

layer3-1-out

for the

sending-side flow detection mode, or delete the sending-side flow detection
mode.

Message

Description

Cannot attach this list because flow detection

mode layer3-1.

If the receiving-side flow detection mode is

layer3-1

, the access list

cannot be applied.
If the receiving-side flow detection mode is

layer3-1

, IPv4 and MAC

access lists can be applied.
To do so, you can use the following commands:

ip access-group

command

mac access-group

command

Cannot attach this list because flow detection
mode layer3-2.

If the receiving-side flow detection mode is

layer3-2

, the access list

cannot be applied.

If the receiving-side flow detection mode is

layer3-2

, IPv4 access lists

can be applied to the Ethernet interface.
To do so, you can use the following command:

ip access-group

command

Message

Description

«
...
851
852
853
854
855
...
»

Содержание AX3630S












































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AX3630S

Бренд: Hama Страницы: 5

SuperStack 3 4900

Бренд: 3Com Страницы: 2

Бренд: Kathrein Страницы: 41

Бренд: Communica Страницы: 5

tecatlantis EASY LED CONTROL 2 PLUS

Бренд: Aquatlantis Страницы: 4

Бренд: Lantech Страницы: 119

Бренд: N-Tron Страницы: 196

Бренд: StarTech.com Страницы: 16

Бренд: GarrettCom Страницы: 76

Бренд: Tenda Страницы: 177

Бренд: LEGRAND Страницы: 140

Master View CS-74A

Бренд: ATEN Страницы: 16

Бренд: AT&T Страницы: 24

Бренд: Wyrestorm Страницы: 2

kontron KSwitch D3 UMP

Бренд: S&T Страницы: 36

Бренд: ATEN Страницы: 2

Бренд: Gefen Страницы: 31

Бренд: IRT Electronics Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды