Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 230

Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 134

OPERATION

RMB 1660 01/22

Operation Section 4-12

© 2022 Alamo Group Inc.

OPERA

T

ION

5.2 Boom Unit Pre-Operation Inspection and Service

Inspect and service the boom arm and head prior to operation. Damaged and/or broken parts should be
repaired and/or replaced immediately. To ensure the unit is ready for operation, conduct the following:

OPS-B- 0020

NOTE

: The mower Operator’s Manual and affixed Decals contain important instructions on the safe and proper

use of the mower. Maintain these important safety features on the mower in good condition to ensure the
information is available to the operator at all times.

All Safety Shields, Guards and Safety devices including (but not limited

to) - the Deflectors, Steel Guards, Gearbox Shields, PTO integral

shields, and Retractable Door Shields should be used and maintained in good working

condition. All safety devices should be inspected carefully at least daily for missing or

broken components. Missing, broken, or worn items must be replaced at once to reduce

the possibility of injury or death from thrown objects, entanglement, or blade contact.

(SFL-5)

Replace bent or broken blades with new blades. NEVER ATTEMPT TO STRAIGHTEN,

WELD, OR WELD HARDFACING ON BLADES SINCE THIS WILL LIKELY CRACK OR

OTHERWISE DAMAGE THE BLADE WITH SUBSEQUENT FAILURE AND POSSIBLY

CAUSE SERIOUS INJURY FROM THROWN BLADES.

(SGM-10)

The operator’s manual and safety signs affixed on
the unit contain important instructions on the safe
and proper use of the equipment. Maintain these
important safety features on the implement in good
condition to ensure the information is available to
the operator at all times.

•

Ensure the manual canister is secured to the
equipment with the operator’s manual inside.

•

Ensure all safety signs are in place and legible.
Replace missing, damaged, and illegible
decals.

OPS-U- 0011

KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement

and possible serious injury or death.

(SG-24)

«
...
132
133
134
135
136
...
»

Содержание BUSH HOG RMB 1660







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды