Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 230

Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 127

OPERATION

RMB 1660 01/22

Operation Section 4-5

© 2022 Alamo Group Inc.

OPERA

T

ION

2. TRACTOR REQUIREMENTS

In addition to tractor horsepower and size required to operate the mower unit, the tractor must also be properly
equipped to provide operator protection, to alert approaching vehicle drivers of the tractor’s presence, and to
ensure tractor stability when mowing with the boom fully extended.

Tractor Requirements and Capabilities

•

Certified approved Roll-Over Protective Structure (ROPS) or ROPS cab and seat belt.

•

Operator Protection .......................... Tractor must be equipped with protective structure such as operator
cage or lexan window to protect operator from thrown object and falling objects

•

Tractor Safety Devices .................... Slow Moving Vehicle (SMV) emblem, lighting,

•

Tractor Ballast ................................. As required to maintain at least 1500 lbs. on left rear tire

Operator Thrown Object Protection

The tractor must be equipped with protective
equipment to shield the operator from falling and
thrown objects. For cab tractors, the tractor must be
equipped with operator protective film on right side
windows and door, or must be fitted with a shatter
proof safety window. For non-cab tractors, the
tractor must be equipped with a ROPS and operator
protective safety cage that provides protection to
the right and above the operator seat. DO NOT
remove the ROPS from non-cab tractors to equip a
safety cage.

2.1 ROPS and Seat Belt

The tractor must be equipped with a Roll-Over-Protective-Structure (ROPS) (tractor cab or roll-bar) and seat
belt to protect the operator from falling off the tractor, especially during a roll over where the driver could be
crushed and killed. Only operate the tractor with the ROPS in the raised position and seat belt fastened.
Tractor models not equipped with a ROPS and seat belt should have these life saving features installed by an
authorized dealer.

OPS-U- 0003

Operate this Equipment only with a Cab Tractor. Always wear seat belts.

(SG-45)

Never operate the Tractor and Mower Unit without an OPS (Operators
Protective Structure) or Cab to prevent injury from objects thrown from
ground or from overhead trimming. Stop mowing if workers or passersby
are within 300 feet.

(SBM-9)

«
...
125
126
127
128
129
...
»

Содержание BUSH HOG RMB 1660







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды