background image

MODEL 1100-I HEARTH CLASSIC PELLET INSERT

INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS

CONGRATULATIONS—You are now the proud owner of one of the finest inserts in the world for your home—the QUADRA-
FIRE!  
Now before installing your insert and building your first fire, record the serial number on the warranty card.  The serial
number is located on the safety label on the back wall of the hopper.

PLEASE READ ALL OF THE OWNER’S MANUAL AND SAFETY NOTES

IMPORTANT SAFETY NOTES

1.

When installing your insert, particular attention should be paid to fire protection. If this unit is not properly installed, a house fire may

result. For your safety, follow the installation instructions, and contact local building or fire officials about restrictions and installation
inspection required in your area.

2.

Read power supply section of component information (page 9) before you plug in the insert.

3.

Always unplug the insert before cleaning or servicing.

4.

Do not connect the insert to a chimney flue already serving another appliance.

5.

Do not connect this heater to any air distribution duct or system.

6.

The insert operates with a negative pressure firebox and a positive pressure exhaust. It is imperative that the chimney system be airtight

and installed correctly.

7.

Dispose of all ashes in a metal container.

8.

Do not burn garbage or flammable fluids such as gasoline, naphtha or engine oil.

9.

Do not use chemicals or fluids such as gasoline, lantern fuel, kerosene, or charcoal lighter fluid to start or freshen up a fire in this insert.

10. HOT WHILE IN OPERATION. Keep children, clothing, flammable liquids and furniture away from heater. Contact may cause skin

burns.

11. Comply with all minimum clearances to combustibles as shown on page 5.
12. The Quadra-Fire 1100-I is tested and approved for pelleted biomass fuel only. Burning of any other type of fuel voids your warranty!
13. Aladdin Hearth Products, manufacturer of the 1100-I pellet insert, reserves the right to alter its products, their specifications and/or price

without notice.
ALADDIN HEARTH PRODUCTS, GRANTS NO WARRANTY, IMPLIED OR STATED, FOR THE INSTALLATION OR
MAINTENANCE OF THIS UNIT AND ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).

North 

America’s 

Best

401 N. Wynne Street
Colville, WA  99114

www.hearth.com/quad
[email protected]

SAVE THESE INSTRUCTIONS

(Revised 3/98)

Содержание Quadra-Fire 1100-I





















Отзывы: