AL-KO Solo 7505 V2R, Инструкция по эксплуатации, Страница: 25 / 113

Maintenance and care
441582_a 25
1. Remove the depth skid.
2. Unscrew the screw plug of the fill opening
(18/1).
3. Tilt the cultivator backwards into position A.
4. Suction up the waste oil with a pump.
5. Fill with new oil. Required oil amount approx.
0.5 l.
6. Measure the oil level to check the filled oil
amount: Tilt the cultivator backwards. Oil
must flow out of the fill opening just before the
cultivator touches the ground.
7. Screw the screw plug into the fill opening
(18/1) again.
8. Always dispose of waste oil in accordance
with legal requirements, e.g. at waste oil ac-
ceptance points.
Replacing the gear oil of the gearbox, 7505
V2R (19) (20)
The gear oil of the gearbox must be replaced
every 60 working hours (amount: 0.9 l, viscosity
SAE 80). The cultivator must be warm in order to
replace the gear oil.
Check the oil level:
1. Place the cultivator on a level surface.
2. Pull the oil dipstick (19/1) out and check that
the oil level is between “Min.” and “Max.”. If
the oil level is below the “Min.” marking, oil
must be refilled.
3. Insert the oil dipstick again.
Draining oil:
1. Pull out the oil dipstick (20/1).
2. Place a collecting container (B) with a capa-
city of at least 1 litre under the manual trans-
mission (20/2).
3. Unscrew the oil drain plug (20/3).
4. Allow the oil to drain completely into the
collecting container (B).
5. Screw in the oil drain plug (20/3) again.
Filling in oil:
1. Fill the manual transmission with new oil
(amount: 0.9 l, viscosity SAE 80) again via the
fill opening (A) of the oil dipstick.
2. Insert the oil dipstick (20/1) again.
3. Check that the oil level is correct (see “Che-
cking the oil level").
Changing the engine oil
See operating instructions of the motor.
Replacing the air filter and spark plug
See operating instructions of the motor.
Readjusting the Bowden cable of the gas le-
ver
See operating instructions of the motor.
Readjust the Bowden cables for the clutch le-
ver and reverse gear (only 7505 VR) (21)
The fine adjustment of a Bowden cable is carried
out with the respective setscrew on the Bowden
cable ends. One setscrew is on the lever on the
handlebar and the other at the attachment point
of the motor clutch or at the attachment point of
the motor gearbox.
The travel of the Bowden cable for the tiller blades
must be set in such a way that the tiller blades
start to turn after the clutch lever (21/1) has travel-
led halfway. If the clutch lever (21/1) or the lever
(21/7) for the reverse gear has been completely
pressed on the handlebar, the associated tension
spring (21/2) must be pulled apart by 8-10 mm.
1. Loosen the locknut of the setscrew on the re-
spective Bowden cable. For the clutch lever:
(21/3) and (21/4). For the lever of the reverse
gear: (21/5) and (21/6).
2. Turn the setscrew to lengthen or shorten the
travel of the Bowden cable.
3. Tighten the locknut again.
STORAGE
WARNING!
Danger of fire - Danger of serious da-
mage to people and property.
Persons can be seriously injured due to
exploding fuel vapours and serious da-
mage to property can occur.
Only store the fuelled appliance in a
well-ventilated area.
Do not store the fuelled appliance
in buildings where fuel vapours can
come into contact with open flames
or sparks.