Akiyama SD2 MIXER, Руководство пользователя, Страница: 8 / 18

7
OP E RATION
E
NGLISH
STUTTER EFFECT
TAP BPM
TEMPO LOCK
MIXER OUTPUT MODE
SYSTEM SETTING
When a loop is playing you can
press RELOOP button to restart
the loop at once. You can also
press this button when a track is
not playing in loop. Every time
the RELOOP button is pressed, it
will restart the music from the pre
programmed cue point. The
stutter effect adds extra creativity
to your performance.
AUTO BPM is the default mode when power on. You can switch
Manual /Auto BPM by pressing the “TAP BPM” button.
Notice:
Switch Manual BPM on just
need one touch the button.
Switch Auto BPM on by pressing
the “TAP BPM” button more
than 1 sec. and then the LCD will
display “AUTO BPM”.
There are two modes for BPM count as below:
following the music tempo and press the “TAP
BPM” button to count BPM value; from the auto BPM to manual
mode, the value won't change until the correct BPM value is
counted.
counting BPM value automatically without
pressing “TAP BPM” button.
Press the PITCH button for more than 2seconds to switch TEMPO
LOCK on/off. ”Pitch Lock” will display when Tempo lock on and
2seconds later icon “PITCH LOCK” will also display in the LCD.
When the MIXED OUTPUT is activated, the internal mixer is
used. You can connect the mixed output of the player directly to an
amplifier or a set of powered speaker cabinets. If the MIXED
OUTPUT is not activated, the output will send player 1 output
signal.
Press the SEARCH button for more than 2 seconds to enter system
setting mode. At this time, LCD display “PRESET” and the
SETUP LED will lit.
Turn the FOLDER knob to scroll
through the different submenus,
you can adjust the setting by
stopping on the desired submenu
and pushing the FOLDER knob.
To exit the system settings, you
can turn the FOLDER knob
counterclockwise to PRESET
submenu and then press the
FOLDER knob.
NOTE: You can also exit the system settings by more than 10
seconds no operation and SETUP LED will go out.
.
Once enter the SETUP mode you can browse the items by turning
FOLDER knob, and pressing FOLDER knob to on or off item
selection, see more details of the different submenus and options
as below:
You can select different time display by pressing
the FOLDER knob to switch between elapsed and remaining. The
default setting is REMAIN TIME.
This function allows you to choose single-track
play or continuous track play (all tracks in order) The default
setting is CONTINUOUS play.
This will indicate if the Auto Cue is on or off. The
default setting is AUTO CUE.
All the tracks in the SD card will play in the
normal mode.
The tracks within one folder are playback. The
default setting is REPEAT OFF.
Press the FOLDER knob to switch the RELAY on and
off.
The left and right players will automatically be in
the continuous play mode.
The left and right players will automatically be in
the single play mode.
The default setting is RELAY OFF.
In the ” Reset all?” section, this will reset all your
programmed menus and restore the unit to its default settings.
Press the FOLDER knob will return all function setting to default
setting automatically and then "reset OK" will display in the LCD.
You may display the unit firmware version Firmware is the unit
internal programming code. Once enter setup mode and then turn
the FOLDER KNOB until Vxx.xx is displayed. “x’s” are the
version number.
Copy the controller or DSP code form PC and then save into
SD card (Files must be in root directory).
Off the controller power cord and re-plug in.
Press STANDBY button to power on
Insert SD card into card A to upgrade version and
”UpdateUIxx” will display in the LCD
When upgrade is done ”COMPLETE” will display
Off the controller power cord and re-plug in. After pressing
the STANDBY to power on, if “UpdateUI - -”
is displayed, please repeat procedure step2 to step5.
Check the version number of the new firmware in the
SETUP MODE
Done
Note:
1. Please delete the code within SD card when upgrade has already
done.
2. Power disconnection or unknown SD card will cause failure.
1. Manual BPM:
2. Auto BPM:
SETUP MODE
TIME MODE -
PLAY MODE -
AUTOCUE -
REPEAT: OFF -
REPEAT: ON -
RELAY -
RELAY: OFF -
RELAY: ON -
-
-
-
RESET ALL -
FIRMWARE VERSION
FIRMWARE upgrade:
Step1:
Step2:
Step3:
Step4:
Step5:
Step6:
Step7:
Step8:
CROSSFADER ACTIVE Only available when MIXER
OUTPUT is ON. Press the FOLDER knob to switch the
CROSSFADER on and off. This fader is used to mix the output
signals of the left and right players.
CROSSFADER: OFF The output signals of both players will be
even.
CROSSFADER: ON
The mix signals from the left and right
players according to the crossfader position.
The default setting is CROSSFADER ON.