manualshive.com logo in svg

AJA kumo 1604, Инструкция по установке и эксплуатации, Страница: 59 / 73

Поделиться
Скачать
AJA kumo 1604 Скачать руководство пользователя страница 59

KUMO SDI Routers and Control Panels v4.7r1 59 www.aja.com

 

Serial Interface

•  1x DB-9 Female, RS-422
•  Basic support for Grass Valley Native Protocol
•  9-pin D-connector pinout is as follows:

1 GND
2 TX-
3 RX+
4 GND
5 

No Connection

6 GND
7 TX+
8 RX-
9 GND
Shell GND

Size (w x d x h)

•  1RU - 17.4” x 1.54” x 1.75” (441.96 x 39.12 x 44.45 mm)

Weight

•  1.2 lb (0.6 kg)

Power

•  External power supply required

•  Enclosure: Dual, redundant, 10-14VDC regulated, 4-pin Molex, 7W typical, 

9.6W max.

•  AC adapter, included: 100-240VAC, 50/60 Hz, universal input, 60W
•  Optional redundant AC adapter sold separately, KUMO-PWR

Environment

•  Safe Operating Temperature: 0 to 40 C (32 to 104 F)
•  Safe Storage Temperature (Power OFF): -40 to 60 C (-40 to 140 F)
•  Operating Relative Humidity: 10-90% noncondensing
•  Operating Altitude: <3,000 meters (<10,000 feet)

KUMO CP2 Tech Specs

User Interface

•  80 buttons with removable overcap for lens chips
•  Includes factory installed lens chip set
•  High and Low button tally indication, configurable brightness
•  Controls up to four KUMO routers
•  Panel Lock feature
•  Destination Lock feature

Router Support

•  KUMO 1604
•  KUMO 1616
•  KUMO 3232

Содержание kumo 1604










































































Отзывы:

Нет отзывов