AJA KONA IP Скачать руководство пользователя

Страница: 61 / 76

KONA IP Transport, Capture, Display v16.0r1 61 www.aja.com

AJA NMOS Controls

When the tray icon is clicked (on the Mac or right click on Windows) the AJA

NMOS application offers a number of options:

• View Log - toggles opening or closing of the log window
• Stop/Start Service - allows the NMOS service to be stopped and restarted

without quitting the application

• Enable/Disable Debug Log - enables or disables the generation of debug

output to the AjaLogger and the log window

• Enable/Disable DNS Debug - enables or disables additional DNS debug

information (independent of Debug Log setting)

• Enable/Disable Verbose Debug - enables or disables additional debug

information if the Debug Log setting is enabled

• Select Interface - NMOS only uses one interface to access the registry. If there

is only one interface, then that is not a problem. If there is more than one, then

if auto is selected, it will automatically choose one based on whether it sees

any mDNS messages on one of the interfaces. Otherwise, the interface can be

selected.

• Set Registry IP - allows the registry ip address and port to be set manually.
• Quit - causes the NMOS application to exit

Transmit Redundancy with ST 2110 via ST 2022-7

For JSON Configuration (Transmit only)

1.  Go into Advanced Ip Config / Generate for JSON
2.  Set Tx Remote to the IP address to which you are sending
3.  Manually set the frame rate in the frame buffer within AJA Control Panel.

Guidance for SMPTE ST 2110-23

For JSON Configuration

1. Go into Advanced Ip Config / Generate for JSON.
2. When doing this behavior is to now automatically set up for 2K/HD on SFP 1,

or 4K/UltraHD across both SFPS.

3. Set Tx Remote to the IP address to which you are sending.
4. On receiving device use this same IP address (i.e. Rx IP address should match

your Tx IP address).

5. Un-check follow input on the receiving KONA IP.
6. Manually set the frame rate in the frame buffer within AJA Control Panel.

For SDPs

1. Change the 4K/UHD network settings in the JSON 4K setup from false to

true.

2. Un-check follow input.

Содержание KONA IP













































































Результаты поиска

Содержание KONA IP

Отзывы:

Похожие инструкции для KONA IP

Бренды по названию

Популярные бренды

AJA KONA IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KONA IP

Отзывы:

Похожие инструкции для KONA IP

Бренды по названию

Популярные бренды