AJA KONA IP Скачать руководство пользователя

Страница: 10 / 76

KONA IP Transport, Capture, Display v16.0r1 10 www.aja.com

KONA IP Features

KONA IP is designed as a flexible platform for supporting various different IP

standards and types:

• SMPTE ST 2110 uncompressed HD video over IP, including Transmit support for

2022-7, thus providing for playout redundancy.

• SMPTE ST 2022-6 uncompressed HD video over IP including support for

2022-7 Transmit and Receive.

• KONA IP can also be configured to use all streams for input or output, thus

supporting up to 4K p60 uncompressed transport via ST 2110-23 (in this case

2022-7 support is not available).

NOTE: NDI is supported on KONA IP in the same way as it is supported on KONA 4,

courtesy of running Newtek Connect.

KONA IP supports different operating modes for different needs. By loading

a different version of firmware, you can tune your AJA hardware to the

requirements of the task at hand.

Video Formats

See

"Appendix A Specifications"

for a listing of supported video formats.

Physical Connection for IP Video

• 2 x 10 GigE Ethernet SFP+ Cages - SFP+ modules (not included).

See

"Appendix A Specifications"

for a list of SFPs tested by AJA.

Inputs and Outputs

• AJA Desktop Software package configured by default for ST 2022-6 operation

with two simultaneous uncompressed streams on the top SFP (one In, one

Out).

• For ST 2022-7 operation, a second SFP is used for redundant transport of the

other SFP's signals.

• When supporting 4K with KONA IP via ST 2110-23, note that both SFPs are

being used in one direction, either input or output.

• KONA IP HDMI output supports HDR signaling and monitoring for HDR10

and HLG. HLG support is application dependent. Check with your software

manufacturer for compatibility.

Digital Audio Input

• 16-Channel embedded audio

Digital Audio Output

• 16-Channel embedded audio, 16- and 24-bit per channel, 48 kHz sample rate,

synchronous

• 8-Channel HDMI embedded audio, 48 kHz sample rate, synchronous

Signal Timing

•  1x BNC assignable to reference video or LTC input
•  Relevant to SMPTE ST 2022-6 workflows only
•  Not used for SMPTE ST 2110 workflows

Содержание KONA IP













































































Результаты поиска

Содержание KONA IP

Отзывы:

Похожие инструкции для KONA IP

Бренды по названию

Популярные бренды

AJA KONA IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KONA IP

Отзывы:

Похожие инструкции для KONA IP

Бренды по названию

Популярные бренды