AJA KONA 4 Скачать руководство пользователя

Страница: 8 / 89

KONA Capture, Display, Convert v15.2 8

www.aja.com

KONA 5 Card with Breakout Cable

Figure 2. KONA 5 Breakout Cable

NOTE: KONA 5 breakout cables cannot be used with KONA 4 cards, and vice versa.

• Up to four channel pairs of AES audio on full size BNC connectors,

configurable as two pairs in and two pairs out, or all four pairs in, or all four

pairs out

•  Reference In/LTC In (selectable)
•  LTC Output
•  RS-422 control via 9-pin D connector

Figure 3. KONA 5 Breakout and Adapter Cables

Digital AES

Audio Input BNCs

Channels 1-8

Digital AES

Audio Output BNCs

Channels 1-8

RS-422 Machine Control

9-pin D-sub (male)

HDMI Output (1)

Reference/LTC Input

SDI I/O 4
SDI I/O 3
SDI I/O 2
SDI I/O 1

LTC Output BNC

LTC Input BNC

5 HD-BNCs

to 5 Standard BNCs

KONA 5

PCIe Bracket

Содержание KONA 4


























































































Результаты поиска

Содержание KONA 4

Отзывы:

Похожие инструкции для KONA 4

Бренды по названию

Популярные бренды

AJA KONA 4, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KONA 4

Отзывы:

Похожие инструкции для KONA 4

Бренды по названию

Популярные бренды