AJA KONA 4 Скачать руководство пользователя

Страница: 69 / 89

KONA Capture, Display, Convert v15.2 69 www.aja.com

Downstream Keyer Screen in 4K Mode

Figure 44. AJA Control Panel, DS Keyer Screen with Unsupported Message

The KONA Downstream Keyer does not support UltraHD/4K formats, but is

available for use with other video formats. If this screen is selected with a

UltraHD/4K format configured, a “Keyer does not support 4K video formats”

message will be displayed.

Control Panel 8K Operation (KONA 5 only)

This section describes the AJA Control Panel operations specific to KONA 5 in

8K Mode. This mode supports the capture or playback of 8K material, using four

input or output 12G-SDI signals. Note that in 8K Mode, you can still capture and

playback single link SD, HD, and 2K formats.
When KONA 5 is operating in 8K mode, the following Control Panel screens are

not available:

•  Audio Mixer
•  DS Keyer
•  LUT

Содержание KONA 4


























































































Результаты поиска

Содержание KONA 4

Отзывы:

Похожие инструкции для KONA 4

Бренды по названию

Популярные бренды

AJA KONA 4, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KONA 4

Отзывы:

Похожие инструкции для KONA 4

Бренды по названию

Популярные бренды