manualshive.com logo in svg

AJA Ki PRO ULTRA, Руководство по установке и эксплуатации

Поделиться
Скачать
AJA Ki PRO ULTRA Скачать руководство пользователя страница 64

Ki Pro Ultra   v1.2r1

www.aja.com

64

 

The buttons in this area can also be used to access the menu parameters in the same way 
that the menu bar on the left hand side of the UI may be used.  The transport buttons in 
this area may be used for clip playback operation.  The UI Control Knob emulation in this 
area may be clicked to toggle from navigating clips to a jog playback mode.  To navigate 
or jog, use a scroll wheel-based mouse or swipe up or down on a trackpad.

Operations Unique to the Web UI

Updating Firmware

The Update Firmware screen allows you to update your Ki Pro Ultra to later versions of 
software as they are issued by AJA and posted on the website. When software updates 
are released, they often contain new features, improvements, and bulletins that may be 
very useful. We suggest checking the website when you have time.

Figure 21. Update Firmware Screen

Although Ki Pro Ultra comes from the factory pre-installed with software, it may not be as 
up-to-date as the software currently posted on the AJA website. This topic describes the 
steps required to upgrade the software in your Ki Pro Ultra.

NOTE: 

AJA recommends a Factory Reset under the CONFIG menu prior to updating firmware.

1. Download the Latest Ki Pro Ultra firmware.

Current and past releases of Ki Pro Ultra firmware are available from AJA's website. To get 
the firmware, point your browser to:

www.aja.com

Access the support page and once you’re at the update page, select the Ki Pro Ultra 
firmware files for Mac or PC for download.

2. Unpack the Software

Содержание Ki PRO ULTRA



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды