AJA Io IP Скачать руководство пользователя страница 32

Страница: 32 / 86

Io IP Transport, Capture, Display v16.2r1 32 www.aja.com

Output Options

Select

• Auto - Automatically selects the output format, based on the input or selected

format.

• Primary - Selects the framebuffer format for output.
• Video+Key - When selected, this indicates that the SDI 3 video is set to the

same format as the framebuffer. SDI 4 is set to a video key signal associated

with SDI 3 (the shape to be cut out from the video - this will appear as a black

and white image/matte). Using the second Io IP output as an Alpha Channel

key, with the video output, may be useful for feeding production switchers,

DVEs or other professional video equipment.

Color Space

Sets the color space. Select from Auto, YUV, or RGB.

RGB Range

Sets the RGB range. Select from Auto, SMPTE, or Full.

3G Transport

Sets the output transport. Select from:

• Auto - Automatically selects the transport, based on the input or selected

format.

•  2xHD-DL - Dual link HD output transport, using two BNCs.
•  3Gb
•  3Ga

HDMI Screen

Содержание Io IP























































































Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды

AJA Io IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды