AJA Io IP Скачать руководство пользователя страница 20

Страница: 20 / 86

Io IP Transport, Capture, Display v16.2r1 20 www.aja.com

AJA Control Panel Operating Modes

AJA Control Panel has two fundamental operating modes.

Playback Mode -

Used for playing back video files from the computer, usually

with a non-linear editing application (NLE) or AJA Control Room, through the

Io IP’s video/audio outputs for viewing and/or external recording.

Capture Mode -

Used for capturing video/audio signals that are coming into the

Io IP from an external source to create video files on the computer using AJA

Control Room or an NLE, or just for display on the Io IP outputs. This mode is

also used for stand-alone video display or conversion when Control Panel is

being used without an external controlling application.

AJA Control Panel User Interface

The AJA Control Panel user interface includes a visual block diagram of the unit’s

current configuration. The current status, input and output settings, and many

other details are depicted in the color-coded block diagram. Below this block

diagram are various controls for changing operating parameters, which will vary

depending on which function screen has been selected.
The left side of the AJA Control Panel provides a navigation list of available

function screens. Clicking on a link (or alternatively, a related element in the block

diagram) displays a function screen corresponding to that topic.

NOTE: Although Io IP is sending and receiving video over IP, once that data is decoded

to memory it is governed by the same video menus used for SDI and HDMI based

AJA I/O solutions.

Figure 5. AJA Control Panel, Block Diagram and Controls

Inputs

Framebuffer

Format

(Primary)

Outputs

Currently

Selected

Function

Screen

Parameter

Controls

AJA Device

Selection

Содержание Io IP























































































Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды

AJA Io IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды