AJA FS2 Скачать руководство пользователя

Страница: 41 / 125

FS2 v2.1r1

www.aja.com

•

Set factory default value

—Push and hold

ADJUST

for 4 seconds to set the parameter to

its factory default value.

•

Save changes

—Parameter value changes are saved within a few seconds. For multiple

values, such as IP addresses, push

ADJUST

momentarily (less than 4 seconds) to save or

take parameter changes.

The remainder of this chapter presents menu examples followed by complete
descriptions of the Menu Groups and Parameter Menus.

Menu Operation Examples

The following examples demonstrate typical menu operation. After this section, each
Menu Group is described in detail.

Status Pages

These steps explain how to surf the

STATUS

menus.

1. Press the

STATUS

Menu Group button.

2. Turn the

SELECT

knob forward and backward to display the

Status

pages. The display

scrolls through the pages as you turn the knob. The

Status

displays simply show the

status of important FS2 operational parameters.

Simple Menus:
Config Format
Alarm Filters

These steps explain how to surf and change simple menus, such as the Power Supply
Alarm Filters.

1. Press the

CONFIG

Menu Group button.

2. Turn the

SELECT

knob to access menu

5 Pwr Supply Alarm

. The default alarm setting is

Normal

3. Turn the

ADJUST

knob one click clockwise to change the setting to

Suppress

, which

turns off the alarm so that it will never come on.

4. Turn the

SELECT

knob clockwise again to access menu

6.1 Vid1 Format Alarm

Changing menus confirms the new

Pwr Supply Alarm

setting.

5. Now change the

Vid1

setting, using the

ADJUST

knob.

Press

STATUS

button and

turn

SELECT

knob to scroll

through

Status

pages.

Settings cannot be changed.

SELECT ADJUST

IN1 SDI1 1080i59
OUT1 525i59 AES/EBU
IN2 SDI2 1080i59
OUT2 525i59 AES/EBU

Current Settings
Current Settings
Current Settings
Current Settings

USO

RESTRITO

Содержание FS2






























































































































Результаты поиска

Содержание FS2

Отзывы:

Похожие инструкции для FS2

Бренды по названию

Популярные бренды

AJA FS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FS2

Отзывы:

Похожие инструкции для FS2

Бренды по названию

Популярные бренды