AJ Aircraft Laser 230z Скачать руководство пользователя | Manualshive

Страница: 7 / 31

background image

Tip

: Install set screws in wheel collar and tighten on axle. Remove the set screws, wheel, and wheel col-

lar and use a file to create a flat for the set screw to rest on. Place a drop of Loctite on them prior to in-

7) Remove the axles, wheels, wheel collars, wrench and lock nuts from the bag. Slide the wheel on the axle and secure with a

wheel collar.

8) To install wheel pants, slide over tire and align horizontally to fit in the wheel pant recess. Using the provided wrench, secure

the axle to the landing gear with a washer and lock nut.

«
...
5
6
7
8
9
...
»

Содержание Laser 230z
































Отзывы:

Нет отзывов

Похожие инструкции для Laser 230z

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

Бренд: S-COM Страницы: 400

Бренд: Paratec Страницы: 8

Бренд: J+J Страницы: 33

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

Бренд: Eaton Страницы: 6

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 22

Бренд: Rabbit Страницы: 38

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды