AIXTRON CRIUS II Скачать руководство пользователя страница 76

Страница: 76 / 194

ius_I

I_e

00,

06/

201

CONFIDENTIAL

AIXTRON

- Dokumentation

Description

System Manual

Gas system

CRIUS II

3.6.5

MO source

An MO source uses metal organic compounds, either in liquid or solid state.
They are provided from containers made of stainless steel (bubbler) which are
passed by a carrier gas. The bubblers are mounted in thermostat heat baths.
See Fig. 3-24,

76.

Several thermostat heat bath types are available. For more information refer
to the related OEM manual.

Fig. 3-24

Thermostat heat bath (example)

A Operating unit

Use the following parameters to control the concentration of the metal organic
compounds in the carrier gas:

•

Temperature of the bubbler

•

Carrier gas flow through the bubbler

•

Pressure in the bubbler

The following versions of the MO source are available:

•

Standard MO source

•

Standard MO source with double bubbler

•

Doping MO source

Содержание CRIUS II



































































































































































































Результаты поиска

Содержание CRIUS II

Отзывы:

Бренды по названию

Популярные бренды

AIXTRON CRIUS II, Системное руководство

Результаты поиска

Содержание CRIUS II

Отзывы:

Бренды по названию

Популярные бренды